Listening to
Radio
Broadcasts
.
t;:l
-- I t----1 |
L*lll
ffi
Selecting an
AM
or
FM
Station
O
Turn
the
receiver
on
@
Press
the
AM
or
FM
Source Select button.
.
lf
you pressed
the AM
Source Select button,
AM
and
kHz
appear
in
the
Tuner
Display
Window. The receiver
tunes
in
the
last AM frequency
that was
played
lf
you pressed
the FM
Source Select button, FM and MHz
appear in the
Tuner
Display Window. The recerver tunes in
the last FM frequency
that was
played.
O
Use
the TUNING key
to
find
the
radio frequency
you
want to
listen
to. Press the right side of the key to find higher frequen-
cies;
press
the left
side of
the key to
find
lower
frequencies.
When
you
release
the
TUNING key,
the
receiver
auto{unes
until
it
tunes a station in. You can stop auto{uning
by
press-
Ing
any
tuner
button.
The TUNED lndicator
lights when the receiver is
tuned
oreciselv
to
either an AM or FM station.
Note:
Tap the TUNING
key momentarily to
change
the fre-
quency
tn
steps
of 10 kHzfor
AM and 0.1 MHzfor
FM.
Hold
the
TUNING key down to change the frequency faster,
then
tAn thq ko\/ tn cpt lho f roar tanav nroaicaltt
lmportant! lf
the
receiver is
tuned to a statton
but
the TUNED
lndicator doesn't light,
try adjusting the
antenna
for
better
reception.
When
you
tune to
an FM station, the receiver
automatically
plays
in stereo; the
STEREO indicator and the AUTO indicator
are lighted.
@
Press
the
FM
MODE/MUTE button
when listening to an FM
station
with
a
weak or noisy signal. Reception wil be
improved, although
you
will be
listening
to
monaural
(non-
stereo) sound.
The STEREO
indicator
and the
AUTO indicator
disaooear.
Presetting an AM or
FM
Station
Vnrrnan ^rocar . tntSl
gf
40 radiO StatiOnS
intO
the
reCeiver'S
memory.
You
preset
a station by assigning
it
a channel
number
(1
to 40) Once a station
has
been
preset, you
can
tune to that station using the
Numeric keys rather than the
TUNING key.
(See
Using Numerrc Keys
'
on
page
1
1.)
Q
Turn
the
receiver
on.
@
Press the AM
or the
FM
Source Select
button,
O
Use the TUNING key to tune
in
the radio station
you
want to
Dreset.
@
Press
the MEMORY button.
The MEMORY indicator lights
and
- -
CH appears
(-
-
blinks)
in
the Tuner Display Window for about
five
seconds.
@
Using the Numeric keys, enter the channel
number
(1
to
a0)
you
want
to assrgn to the statron.
The channel number appears in the Tuner Display Window.
lmportant! You must
enter
the channel number while the
MEMORY
indrcator
is
lighted.
lf the
indicator
turns off too
soon,
press
the MEMORY button and start again.
Repeat
the above
process
to
preset
additional
radio
stations.
Note: Preset
stattons are
held in
the
receiver's memory as
long
as the receiver
is
plugged
in. lf
the
receiver is un-
plugged,
or
if
a
power
fatlure
occurs, the
receiver will keep
the
presets
for
two or three days before erasrng
them.
P2^a 1n
To Next Page
Loading...
Need help?
General
