JVC RX-230RBK - Listening Enhancements; Loudness Function; Surround Sound Effect; Sleep Timer Function

To use the EON function:
ON/OFF Press the ON/OFF button either on the front panel or EON button on the remote control.
© The EON indicator lights up on the display, and the receiver enters EON standby mode.
if there is no station broadcasting the program
you have selected
The receiver continues playing the current source.
Sue
When a station starts broadcasting the program you have
selected, the receiver automatically switches to the station. The
EON indicator starts blinking.
a
When the program is over, the receiver goes back to the
previously selected source, but still remains in EON standby
If there is a station broadcasting the program
you have selected
The receiver stops playing the current source, and tunes in the
program. The EON indicator starts blinking.
se
When the program is over, the receiver goes back to the
previously selected source. but still remains in EON standby
mode.
Operating Audio Components
COUMADIN
wwii wv wat
Ili/Remote ill
Remote Control
Automatic Source Selection
COMPU LINK Remote Control System
The COMPU LINK remote control system lets you operate the receiver and JVC components
from the remote control supplied with this receiver, Control signals for JVC audio components
are preset in the receiver's remote control.
Connecting the COMPU LINK-3 SYNCHRO jacks on the rear of the receiver will allow you
to use the four functions listed below.
You can contro} all components via the remote sensor on the receiver using the receiver's
remote control. For details, sec page 21.
IMPORTANT! Aim the remote control directly at the remote sensor on the receiver.
When you press the play () button on a connected component or on its own remote control,
the receiver automatically turns on and changes the source to the component. On the other hand,
if you select a new source on the receiver or the remote control, the selected component begins
playing immediately.
El-k
mode. In both cases, the previously selected source continues playing without sound for a few seconds.
Synchronized recording means the cassette deck starts recording as soon as a CD or record
begins playing.
To stop listening to the program selected by EON: Synchronized Recording
Press the ON/OFF button on the front panel or the EON button on the remote control again so
that the EON indicator on the display goes off. The receiver enters EON off mode and goes back
to the previously selected source.
Each time you press the ON/OFF button on the front panel or the EON button on the remote
control. the EON mode alternates between standby mode and off mode.
To use synchronized recording, follow these steps:
Step 1 Puta tape in the cassette deck, und a dise in the CD player (or a record on the turntable).
Step 2 Press the record (@) button and the pause (fH) button on the cassette deck at the same
time.
This puts the cassette deck into recording pause.
NOTES:
* In EON standby mode, if you change the source to AM (MW/LW) or if you carry out
svachronized recording (see page 20), EON standby mode is canceled temporarily. Ret :
: e Poe : " NOTE: If you do not press the record (@) button and pause (W) button at the same time,
The receiver goes back to EON standby mode again when vou have finishe : 5 .
He RECEIVE G i te age en vou have finished that the synchronized recording feature will not operate.
operation.
+ While listening to a program tuned in by the EON function, you can only use the
STANDBY/ON U1, ON/OFF, and DISPLAY buttons on the front panel or the
AUDIO Oi|, EON, and DISPLAY MODE buttons on the remote control.
+ When the receiver is turned off. the FON function is also turned off.
Step 3 Press the play (®) button on the CD player or on the turntable.
The source changes on the receiver, and as soon as play starts, the cassette deck starts
recording. When the play ends, the cassette deck enters recording pause, and stops
4 seconds later.
NOTES:
IMPORTANT! When the source alternates intermittently between the station tuned in ¢ During synchronized recording, the selected source cannot be changed.
by the EON function and the currently selected source, press the ON/OFF button * ff your CD player is playing in program mode, a 4-second blank is recorded
on the front panel or EON button on the remote control to cancel the EON between tracks so that the music scan feature of your cassette deck can be used on
function
(the
EON
indicator
goes
off}.
This
is
not
a
malfunction
of
the
receiver.
the
recorded
tape.
° Uf the power of any component is shut off during synchronized recording, the
COMPU LINK remote control system may not operate properly. In this case, you
must start again from the beginning.
* Refer also to the manuais supplied with your CD plaver and cassette deck.
Both the CD player and cassette deck turn on and off with the receiver.
When you turn on the receiver, the CD player or cassette deck will automatically turn on.
depending on which component has been previously selected.
When you turn off the receiver, both the CD player and cassette deck will turn off,
Automatic Power
standby/on
NOTE: This function has been added to COMPU LINK-3 (Enhanced COMPU LINK),
an upgraded version of COMPU LINK-/ and -2.
Page 19 Page 20
MadOee-XY