Need help?Do you have a question about the Keyscan CA8WL-AL and is the answer not in the manual?
General| Brand | Keyscan |
|---|---|
| Model | CA8WL-AL |
| Category | IP Access Controllers |
| Language | English |
This guide reviews installation information for the Keyscan CA8WL-AL access control unit.
Safety measures concerning electrical connections and power application during installation.
List of recommended tools required for installing the access control system.
Describes that CA8WL-AL inputs, outputs, and reader terminals are disabled.
Specifies the compatible Keyscan software versions for the CA8WL-AL control unit.
Details the available power sources for the CA8WL-AL control unit.
Explains the necessity and process of programming the on-board Ethernet module.
Outlines procedures for setting up reverse network communication, requiring a license.
Refers to separate documentation for PIM400-485/Schlage AD-400 wireless locks.
Step-by-step instructions for physically mounting the CA8WL-AL unit.
Details the functions regulated by system configuration DIP switches S1.1 through S1.12.
Explains the S1.1 DIP switch setting for serial, network, or reverse network communication.
Describes the S1.2 DIP switch for selecting the control board's communication bit rate.
Explains how the S1.3 DIP switch can override the P3 cardholder lockout mode.
Details the S1.4 DIP switch for selecting an alternate panel serial number.
States that the S1.5 DIP switch is not applicable.
Indicates that the S1.6 DIP switch is reserved for future use.
Explains enabling the temporary card countdown function via the S1.7 DIP switch.
States that the S1.8 DIP switch is not applicable.
Describes enabling the J1 Clear Memory jumper via the S1.9 DIP switch.
Explains how S1.10 and S1.11 activate RS-232 or Ethernet communication terminals.
States that the S1.12 function for flash program memory upgrade is currently unavailable.
Details the procedure to restore factory default settings using jumper J1.
Outlines the communication modes between CA8WL-AL and the server/workstation.
Details the requirements and procedures for network (TCP/IP) communication.
Describes the connection of the CA8WL-AL to the PIM400-485 unit via RS485.
Clarifies that the CA8WL-AL is a stand-alone unit and does not support other control units.
Specifies the maximum number of wireless locks supported per CA8WL-AL/PIM400-485 kit.
Provides instructions on configuring a 9-pin RS-232 data cable for serial connections.
Offers important notes regarding the installation and connection of RS-232 cables.
Details the built-in PoE power supply capabilities and current rating of the CA8WL-AL.
Explains how to power the CA8WL-AL using a +12V DC UL approved power supply.
Provides instructions for powering up the CA8WL-AL unit via PoE or 12V DC supply.
Explains the function and states of the communication LEDs on the CA8WL-AL control board.
Describes the tri-colour System Status LED and its indications.
Lists essential items needed before programming the CA8WL-AL's on-board Ethernet module.
Guides on installing the Keyscan NETCOM Program Utility software.
Provides steps to program the CA8WL-AL's on-board Ethernet module.
Explains the concept and requirements of reverse network communication.
Specifies the NETCOM Program Utility version required for reverse network configuration.
Details coordination needed between host and remote locations for reverse network setup.
Explains the format, creation, and use of encryption keys for reverse network communication.
Guides on setting DIP switches S1.1 and S1.2 for reverse network communication.
Provides steps to set the IP address on the access control board using Hyper Terminal.
Summarizes the ACU's connection attempts and behavior in reverse network mode.
Details the warranty terms, coverage, and limitations for Keyscan manufactured products.
Outlines the seller's rights regarding possession of goods for credit reasons or defaults.
States buyer's responsibility for proper selection, installation, and operation of the product.
To Next Page