Keysight PXA N9030A - Page 90

3 Programming the Analyzer
List of SCPI Commands
[:SENSe]:METer[1]|2|3:DETector POSitive | QPEak | EAVerage | RAVerage |
AVERage | NEGative
[:SENSe]:METer[1]|2|3:DETector?
[:SENSe]:METer:DETector:DWELl <time>
[:SENSe]:METer:DETector:DWELl?
[:SENSe]:METer:GAIN:AUTO ON | OFF | 1 | 0
[:SENSe]:METer:GAIN:AUTO?
[:SENSe]:METer:PHOLd:ADJustable <time>
[:SENSe]:METer:PHOLd:ADJustable?
[:SENSe]:METer:PHOLd:RESet
[:SENSe]:METer:PHOLd:TYPE INFinite | ADJustable
[:SENSe]:METer:PHOLd:TYPE?
[:SENSe]:MONitor:DEMod AM | FM | OFF
[:SENSe]:MONitor:DEMod?
[:SENSe]:MONitor:DEMod:FM:DEEMphasis OFF | US25 | US50 | US75 | US750
[:SENSe]:MONitor:DEMod:FM:DEEMphasis?
[:SENSe]:MONitor:FREQuency:SPAN <frequency>
[:SENSe]:MONitor:FREQuency:SPAN?
[:SENSe]:MONitor:FREQuency:SPAN:PREVious
[:SENSe]:MONitor:SPECtrum:BANDwidth[:RESolution] <freq>
[:SENSe]:MONitor:SPECtrum:BANDwidth[:RESolution]?
[:SENSe]:POWer[:RF]:ATTenuation <rel_ampl>
[:SENSe]:POWer[:RF]:ATTenuation?
[:SENSe]:POWer[:RF]:GAIN:BAND LOW | FULL
[:SENSe]:POWer[:RF]:GAIN:BAND?
[:SENSe]:POWer[:RF]:GAIN[:STATe] OFF | ON | 0 | 1
[:SENSe]:POWer[:RF]:GAIN[:STATe]?
[:SENSe]:POWer[:RF]:MMW:PADJust
[:SENSe]:POWer[:RF]:MW:PADJust
[:SENSe]:POWer[:RF]:PADJust <freq>
[:SENSe]:POWer[:RF]:PADJust?
[:SENSe]:POWer[:RF]:PADJust:PRESelector MWAVe | MMWave | EXTernal
[:SENSe]:POWer[:RF]:PADJust:PRESelector?
[:SENSe]:POWer[:RF]:PCENter
[:SENSe]:POWer[:RF]:RFPSelector[:STATe] 1 | 0 | ON | OFF
[:SENSe]:POWer[:RF]:RFPSelector[:STATe]?
[:SENSe]:ROSCillator:BANDwidth WIDE | NARRow
[:SENSe]:ROSCillator:BANDwidth?
[:SENSe]:ROSCillator:EXTernal:FREQuency <freq>
[:SENSe]:ROSCillator:EXTernal:FREQuency?
[:SENSe]:ROSCillator:SOURce INTernal | EXTernal
[:SENSe]:ROSCillator:SOURce?
[:SENSe]:ROSCillator:SOURce:TYPE INTernal | EXTernal | SENSe | PULSe
[:SENSe]:ROSCillator:SOURce:TYPE?
[:SENSe]:SCAN[1]|2|...|10:BANDwidth[:RESolution]
[:SENSe]:SCAN[1]|2|...|10:INPut:ATTenuation
[:SENSe]:SCAN[1]|2|...|10:INPut:ATTenuation:AUTO
[:SENSe]:SCAN[1]|2|...|10:INPut:ATTenuation:AUTO
[:SENSe]:SCAN[1]|2|...|10:INPut:GAIN:AUTO
[:SENSe]:SCAN[1]|2|...|10:INPut:GAIN:AUTO
[:SENSe]:SCAN[1]|2|...|10:INPut:GAIN[:STATe] ON | OFF | 1 | 0
[:SENSe]:SCAN[1]|2|...|10:INPut:GAIN[:STATe]?
[:SENSe]:SCAN[1]|2|...|10:INPut:TYPE
90 EMI Receiver Mode Reference