Kodak i1440 - User Manual

Questions and Answers

S
Summer SaundersAug 21, 2025
Why is my Kodak i1440 not scanning or feeding documents?
- K
  Kaitlin HutchinsonAug 22, 2025
  If your Kodak Scanner won't scan or feed documents, ensure the following: * The power cord is properly plugged in and the power is switched on. * The power switch is on, and the green LED indicator is illuminated. * The scanner cover is completely closed. * Documents are making contact with the feed module. * The height of batched documents is less than 10.2 mm (0.4 in.) or approximately 150 sheets of 60 g/m2 (16 lb.) paper. * Documents meet the specified size, weight, and type requirements. * For thicker documents, the gap release lever is lifted during feeding. * Inspect the feed module and separator module for wear and replace them if needed. You can also try powering the scanner off and then on again.
H
hlewisAug 23, 2025
What to do if my Kodak i1440 is jamming or feeding multiple documents?
- T
  Thomas EdwardsAug 25, 2025
  If documents are jamming or multiple documents are feeding in your Kodak Scanner, make sure that: * The output tray and side guides are adjusted for the length and width of the documents being scanned. * All documents meet the specifications for size, weight, and type. * All staples and paper clips have been removed from the documents. * All rollers and tires are clean and the separator module and feed module are properly installed. To remove a document jam: * Remove any documents from the feeder area. * Push up on the scanner cover release latch and open the scanner cover. * Locate the jammed document and remove it. * Close the scanner cover with both hands; push it down firmly until it latches into place. Resume scanning.
B
Brittney ThompsonAug 26, 2025
What to do if long documents jam in Kodak i1440?
- D
  Daniel TurnerAug 26, 2025
  If 35.6 cm (14 in.) or longer documents are not feeding or are jamming in your Kodak Scanner, make sure that the input and output tray extenders are pulled out to provide support for long documents.
B
Brian OnealAug 28, 2025
Why do the lamps shut off too soon on my Kodak i1440 Scanner?
- M
  Melissa FloresAug 28, 2025
  The lamps in the Kodak i1400 Series Scanners will turn off after 15 minutes of no scanner activity. If the lamps are off, but the scanner has not yet gone into the Energy Star mode (default 15 minutes), there will be a delay of about 10 seconds for the lamps to warm up again. If you set the Energy Star timeout to a new value greater than 15 minutes, you must scan at least one document for that setting to be enabled. After this setting has been enabled, it will be enforced until a new setting is selected or the scanner is powered off and back on.
J
Justin KimAug 30, 2025
How to fix skewed documents when scanning with Kodak Scanner?
- T
  Timothy CooleyAug 30, 2025
  If your Kodak Scanner is skewing documents during scanning, ensure that: * The side guides are adjusted to fit the documents being fed. * Documents are being fed perpendicular to the feed module. * Documents are being fed in the center of the feeder. * All staples and paper clips have been removed from the documents. * The feed module, separator module, and drive rollers are clean. * The scanner cover is firmly closed and latched.
A
Ariel JohnsonSep 1, 2025
Why is my Kodak i1440 running so slow?
- J
  Joel BaileySep 1, 2025
  If your Kodak Scanner is running slow, it might be because your PC doesn't meet the minimum requirements. The scanner is designed to work with USB 2.0, but it can function with a USB 1.1 port. If you're using a USB 1.1 connection, try updating to USB 2.0.
M
Matthew SteinSep 3, 2025
Why does my Kodak Scanner pause a lot during scanning?
- L
  Laura CooperSep 3, 2025
  If your Kodak Scanner pauses excessively during scanning, ensure that: * The host computer meets the minimum requirements for scanning. * There is enough free space on the hard disk drive. * All other applications are closed. * The USB connection is 2.0. You can also try changing the scanning options (compression, etc.) in your scanning application.
R
Robert GreerSep 5, 2025
How to improve poor image quality on Kodak i1440 Scanner?
- T
  Tammy ParkSep 5, 2025
  If the image quality of your Kodak Scanner is poor or has decreased, make sure that the scanner and imaging guides are clean.
K
Kevin CabreraSep 7, 2025
What causes multifeeding in Kodak Scanner and how to resolve it?
- K
  Kayla TurnerSep 7, 2025
  If your Kodak Scanner is multifeeding documents, make sure that: * The leading edges of all batched documents are centered in the feeder so that each document will come in contact with the feed rollers. * The feed module and separator module are clean and not worn. * Documents with an unusual texture or surface are fed manually.
T
Terri SchmittSep 10, 2025
How to remove roller marks from Kodak i1440?
- L
  Laura LewisSep 10, 2025
  If roller marks or streaks appear on documents after scanning with your Kodak Scanner, clean the feed module, separator module, and rollers.