Konecranes CU1 - APPENDIX 1: CU1 Passwords

26.03.1996 • KHH SEENXL13A
•For Authorized KCI Service Agents Only•
KCI Hoists Corporation reserves the right to alter or amend the above information without notice
Page 23
XL
Service Manual
CU1
KCI KONECRANES GROUP
KCI HOISTS CORPORATION
APPENDIX 1:
APPENDIX 1:APPENDIX 1:
APPENDIX 1: CU1 passwords
CU1 passwordsCU1 passwords
CU1 passwords
Note:
Note:Note:
Note: These passwords are to be used only by KCI Konecranes service
These passwords are to be used only by KCI Konecranes serviceThese passwords are to be used only by KCI Konecranes service
These passwords are to be used only by KCI Konecranes service
organizations and their authorized service agents.
organizations and their authorized service agents.organizations and their authorized service agents.
organizations and their authorized service agents.
Password_1
Password_1Password_1
Password_1 Password_2
Password_2Password_2
Password_2 Password_3
Password_3Password_3
Password_3
1-000
1-0001-000
1-000 CU1 information
CU1 informationCU1 information
CU1 information (> P2.12)
Displays the program version, hoist class code and selected/valid functional
options
(e.g. P2.12; CL2; OPt2).
1-001
1-0011-001
1-001 Additional information of the use of hoist
Additional information of the use of hoistAdditional information of the use of hoist
Additional information of the use of hoist (> P2.12)
Displays the
-St-h
St-hSt-h
St-h (number of starts per last hour)
-LSt-h
LSt-hLSt-h
LSt-h (largest number of starts per hour)
-St-10
St-10St-10
St-10 (number of starts per last 10 min.) (> P2.13)
-LS-10
LS-10LS-10
LS-10 (largest number of starts per 10 min.) (> P2.13)
-bPC
bPCbPC
bPC (how many times password 1-125 has been used)
-OH
OHOH
OH (how many times the hoisting motor has been overheated)
-brFC
brFCbrFC
brFC (how many times the 'brake wear sensor' has been in warning
state).
1-010
1-0101-010
1-010 Setup counter
Setup counterSetup counter
Setup counter (> P2.12)
Displays the
- SUPC
SUPCSUPC
SUPC (how many times the setup routine has been carried out)
-SPCC
SPCCSPCC
SPCC (how many times password 3-511 has been used).
-hotrt
hotrthotrt
hotrt (for how long the overheated hoisting motor has been used for
lowering) (> P2.13)
1-011
1-0111-011
1-011 Load sensor calibrating voltages
Load sensor calibrating voltagesLoad sensor calibrating voltages
Load sensor calibrating voltages (> P2.12)
Displays the load sensor voltages:
- 0% load as '0-x.xx
0-x.xx0-x.xx
0-x.xx'
- 100% load as '1-x.xx
1-x.xx1-x.xx
1-x.xx'
- existing load as 'L-x.xx
L-x.xxL-x.xx
L-x.xx'
- negative breaking load as 'UL-20
UL-20UL-20
UL-20' or 'UL-10
UL-10UL-10
UL-10' (i.e. load -20% or -10%).
Note the accuracy is ±0,15 VDC.
1-020
1-0201-020
1-020 Decimals for SWP, RT and Starts values
Decimals for SWP, RT and Starts values Decimals for SWP, RT and Starts values
Decimals for SWP, RT and Starts values (> P2.13)
By using this password the exact values for SWP, RT and STARTS from the
values displayed (mm for minutes and ss for seconds).
- SWP (-mm.ss)
SWP (-mm.ss)SWP (-mm.ss)
SWP (-mm.ss) By reducing this value from the displayed SWP value, the
exact SWP value can be calculated.
- RT (mm.ss)
RT (mm.ss)RT (mm.ss)
RT (mm.ss) By adding this value to the displayed RT value, the exact RT
value can be calculated.
- STARTS
STARTSSTARTS
STARTS By adding this value to the displayed RT value, the exact STARTS
value can be calculated.