Krone EasyCut F 320 CV

To Previous Page

Maschinenfabrik

Bernard Krone GmbH

Heinrich-Krone-Straße 10, D-48480 Spelle

Postfach 11 63, D-48478 Spelle

Phone +49 (0) 59 77/935-0

Fax +49 (0) 59 77/935-339

Internet: http://www.krone.de

eMail: info.ldm@krone.de

Main Page

Table of Contents3
Foreword6
To this Document7
Validity7
Direction Information7
Representation and Utilization of Warning Notes7
Identification of the Hazard Warnings7
Purpose of Use8
Intended Use8
Service Life of the Machine8
Safety Instructions and Accident Prevention Regulations9
Personnel Qualification and Training10
Dangers in Case of Non-Compliance with the Safety Instructions10
Safety-Conscious Work Practices10
Attached Devices11
PTO Operation11
Hydraulic System12
Maintenance13
Unauthorised Conversion/Modification and Spare Parts Production13
Inadmissible Modes of Operation13
Machine Description14
Machine Overview14
Identification Plate22
Information Required for Questions and Orders22
Contact22
Introduction23
Re-Ordering the Adhesive Safety and Information Labels23
Affixing the Adhesive Safety and Information Labels23
Position of the Adhesive Safety Stickers on the Machine24
Technical Data of the Machine40
Technical Data40
Consumables46
Filling Quantities and Lubrication Designations for Gearboxes46
Commissioning47
Special Safety Instructions47
First Installation47
Adapting to the Tractor47
Mounting Onto the Tractor48
Clutching Points48
Lower Suspension Arm49
PTO Shaft50
Length Adjustment50
Preparation on the Front-Mounted Disc Mower51
Install the PTO Shaft51
Start-Up52
Preparations on Tractor52
Install the PTO Shaft53
Mounting and Adjusting the Relief Springs54
Pushed Design54
Checking Spring Retaining Chain56
Trailed Design57
Tensioning Guard Cloth57
Lighting Connection58
Hydraulics59
Special Safety Instructions59
Connecting the Hydraulic Lines59
Trial Run after First Installation60
Checking Fitting61
Driving and Transport62
Lighting62
Clamp and Buffer64
Operation65
Before Mowing65
Tensioning Guard Cloth66
Moving the Guards into the Working Position66
Moving Guards into Transport Position67
Parking Support67
Detaching the Machine68
Dismounting Retaining Chains68
Settings69
Adjusting the Compensation Springs69
Pushed Design70
Trailed Design71
Adjusting the Cutting Height72
Telescopic Upper Suspension Arm72
Setting Conditioner Speed73
Changing Pulley74
Replacing Pulley75
Tensioning Belt Drive75
Adjusting the Conditioner Plate76
Adjustment for Swathing76
Wide Spreading77
Setting the Distance of the Rollers78
Maintenance79
Special Safety Instructions79
Test Run79
Spare Parts79
Maintenance Table80
Tightening Torques81
Metric Thread Screws with Control Thread81
Metric Thread Screws with Fine Thread82
Metric Thread Screws with Countersunk Head and Hexagonal Socket82
Deviating Torque83
Intermediate PTO Shaft83
Rotary Hub with Shear Fuse (Optional)84
After Shearing off88
Maintenance - Gearbox90
Input Gearbox90
Angular Gearbox91
Angular Gearbox92
Top Part92
Angular Gearbox93
Bottom Part93
Gearbox for Top Roller Drive94
Tensioning Belt Drive95
Oil Level Check and Oil Change on the Cutter Bar96
Oil Change96
Checking the Oil Level96
Aligning the Cutter Bar96
Maintenance - Blade Changing98
Checking the Cutter Blades and Blade Holder98
Cutter Blades99
Blade Screw Connection100
Blade Quick-Fit Device101
Periodical Inspection of the Leaf Springs102
Periodical Inspection of the Cutting Discs / Blade Drums103
Abrasion Limit104
Blade Changing on Cutting Discs105
Blade Screw Connection106
Blade Quick-Fit Device107
Replacing the Linings108
Maintenance - Lubrication Chart109
Special Safety Instructions109
Universally-Jointed Drive Shaft109
Intermediate PTO Shaft110
Lubrication Chart110
Placing in Storage111
Before the Start of the New Season112
Special Safety Instructions112
Test Run112
Friction Clutch113
Special Equipment114
Special Safety Instructions114
Adjusting Skids114
Disposal of the Machine115
Index116

Krone EasyCut F 320 CV - Page 118

Table of Contents

Other manuals for Krone EasyCut F 320 CV

Related product manuals