Why does the combination instrument display nothing on my KTM 2011 690 SMC EU Motorcycle?
If the combination instrument shows nothing in the display on your KTM Motorcycle, it is possible that fuse 1 is blown. Replace the fuse.
General| Engine Type | Single cylinder, 4-stroke |
|---|---|
| Displacement | 654 cc |
| Bore x Stroke | 102 mm x 80 mm |
| Compression Ratio | 11.8:1 |
| Starter | Electric starter |
| Transmission | 6-speed |
| Cooling | Liquid cooled |
| Rear Suspension | WP Monoshock |
| Suspension Travel Front | 275 mm |
| Suspension Travel Rear | 250 mm |
| Front Tire | 120/70 ZR17 |
| Rear Tire | 160/60 ZR17 |
| Steering Head Angle | 63.5° |
| Seat Height | 890 mm |
| Power | 67 hp |
| Torque | 65 Nm |
| Fuel System | Electronic Fuel Injection |
| Clutch | Wet multi-disc clutch, hydraulically operated |
| Frame | Steel trellis frame |
| Front Suspension | WP USD Ø 48 mm |
| Front Brake | Brembo four-piston radial caliper, 320 mm disc |
| Rear Brake | Single 240 mm disc |
| ABS | Yes, switchable |
| Front Rim | 3.50 x 17 |
| Rear Rim | 5.00 x 17" |
| Tank Capacity | 12 liters |
| Wheelbase | 1480 ± 15 mm |
Defines intended use, service requirements, warranty, and fuel specifications.
Covers spare parts, work rules, transport, environmental responsibility, and warnings.
Explains risk grades (Danger, Warning, Caution, Note) and importance of the owner's manual.
Labeled diagram illustrating components from the front left perspective.
Labeled diagram illustrating components from the rear right perspective.
Location and importance of chassis, engine, and key identification numbers.
Identifies part numbers for specific components like fork and shock absorber.
Operation of levers, switches, buttons, and the ignition/steering lock.
Details on display, indicators, trip meters, speedometer, and clock.
Operation of filler cap, seat release, handrails, footrests, and stands.
Guidance for initial operation, engine break-in, and rider preparation.
Instructions for safe weight distribution and maximum load limits.
Essential checks and maintenance before riding.
Steps for starting, moving off, shifting gears, and general riding advice.
Proper braking methods, conditions, and stopping distances.
Procedures for parking, securing, and refueling the motorcycle.
Maintenance tasks and intervals for different service periods.
Tuning fork and shock absorber compression and rebound damping.
Cleaning, tensioning, and inspection of drive chain and sprockets.
Adjusting clutch lever and checking hydraulic fluid.
Adjusting hand brake lever and checking brake disc wear.
Checking/adding brake fluid and inspecting brake linings.
Step-by-step guide for fitting and removing front/rear wheels.
Checking tire condition, pressure, age, and spoke tension.
Battery removal, installation, and charging procedures.
Guidance on replacing main and individual fuses.
Headlight mask, bulb replacement, and beam adjustment.
Procedures for checking coolant level and antifreeze protection.
Procedures to drain and refill the cooling system.
Adjusting throttle cable play and selecting engine performance maps.
Checking oil level, changing oil/filter, and cleaning oil screens.
Correct method for adding engine oil to maintain proper level.
Recommended methods for washing, drying, and protecting the motorcycle.
Advice for winter use and corrosion prevention.
Steps for preparing and storing the motorcycle for extended periods.
Steps to take the motorcycle out of storage and prepare it for riding.
Key technical data for the engine and fluid capacities.
Technical details on chassis, suspension, tires, and fuel capacity.
Lists of recommended brake fluids, coolants, oils, and fuel types.
Recommended auxiliary products for motorcycle maintenance and cleaning.
To Next Page
