To Next PageTo Next PageHow to resolve 'Send error. ####' on Kyocera Printer?
If your Kyocera printer displays the error 'Send error. ####', use COMMAND CENTER and register the SMTP server name and the host name correctly because the server name of the SMTP server is not set correctly or the host name is incorrect when sending scan data to an FTP server.
What to do if my Kyocera Printer is not printing?
If your Kyocera printer is not printing, first, ensure the power cord is plugged into an AC outlet and that the main power switch is turned on. Check that the printer cable is securely connected. If the printer cable was connected before powering on the machine, power cycle the printer. Finally, verify that the print job is not paused; if it is, press the Resume key to resume printing.
What to do if my Kyocera Printer printouts are too light?
If your Kyocera printer's printouts are too light, several factors could be the cause. If the machine is in Auto Density mode, set the correct density level. If it's in Manual Density mode, select the correct density level. Shake the toner container from side to side to distribute the toner evenly. If there's a message indicating the need for toner, replace the toner container. Damp paper can also cause light prints, so replace the paper with new paper. Finally, check if EcoPrint mode is enabled and, if so, disable it.
How to fix dirty printouts from Kyocera Printer?
If your Kyocera printer produces dirty printouts, the platen or document processor may be dirty, so clean them. Also, the charger wire could be dirty, so ensure you clean that as well.
How to resolve 'Insufficient memory. Cannot start the job' message on Kyocera Printer?
If your Kyocera printer displays the message 'Insufficient memory. Cannot start the job', press the OK key to print the scanned pages or press the Cancel key to cancel the printing job.
Why are my Kyocera Printer images skewed?
Skewed images from your Kyocera printer can result from incorrect placement of the originals or improperly loaded paper. When placing originals on the platen, ensure they are aligned with the original size indicator plates. Also, check the position of the paper width guides to ensure the paper is loaded correctly.
What to do if my Kyocera FS-1028MFP All in One Printer cannot print?
If your Kyocera All in One Printer is not printing, ensure: * The power cord is plugged into an AC outlet. * The main power switch is turned on. * The printer cable is securely connected. * The machine was powered on after connecting the printer cable. * The print job is not paused; press [Resume] if needed.
Why is my Kyocera FS-1028MFP All in One Printer ejecting blank sheets?
If your Kyocera All in One Printer ejects blank sheets, check if the originals are loaded correctly. When using the platen, place originals face-down and aligned with the original size indicator plates. When using the optional document processor, place them face-up.
What to do if nothing lights up on my Kyocera All in One Printer?
To resolve this, ensure the power cord is securely plugged in and set the power switch to the on position. If the device is off, turn the machine’s power on.
How to resolve 'Load paper in MP Tray' error on Kyocera Printer?
If your Kyocera printer displays the 'Load paper in MP Tray' message, load the paper in the multi purpose tray which is of the size and type indicated on the Message Display.
General| Duplex printing | Yes |
|---|---|
| Print technology | Laser |
| Maximum resolution | 1200 x 1200 DPI |
| Time to first page (black, normal) | 6 s |
| Print speed (black, normal quality, A4/US Letter) | 28 ppm |
| Grayscale levels | 256 |
| Maximum copy resolution | 600 x 600 DPI |
| Time to first copy (black, normal) | 6.9 s |
| Internal memory | 256 MB |
| Dimensions (WxDxH) | 494 x 410 x 366 mm |
| Power requirements | 220 - 240 |
| All-in-one functions | Copy, Scan |
| Maximum internal memory | 0.768 GB |
| Compatible operating systems | Windows 2000/XP/Server2003/Vista/7/Server2008 |
| Duty cycle letter size (maximum) | 2800 pages per month |
| Standard interfaces | USB 2.0 |
| Power consumption (standby) | 88 W |
| Power consumption (average operating) | 494 W |
| Non-ISO print media sizes | Folio |
| Maximum duty cycle | 20000 pages per month |
| Market positioning | Business |
