2-10
2. Windows KX Driver
■ Staple
Stapling is possible if the optional finisher is installed.
* The following settings are required before stapling is possible:
(1) “Device Options” setting in the “Device Settings” Tab
• Select [Finisher] or [Multi Finisher].
(2) “Output” Tab
• When the Finisher is installed, select [Tray A (Face-down)] as the “Output to” setting.
• When the Multi Finisher is installed, select [Tray A (Face-down)] or [Tray B (Face-down)] as the “Output to” setting.
• When the Multi Tray is installed, select [Tray 1,2,3,4,5 (Face-down)] as the “Output to” setting.
• When the Folding Unit is installed, select [Folding Unit] as the “Output to” setting. And then, “Booklet Stitch” will be selected
automatically.
• Put a check mark in the checkbox for [Staple] and select the desired type of stapling you want to perform.
• When [Booklet] is selected, [...] box is displayed. Click on [...] box and select the position (Left, Right, Upper) of the stapling you
want perform.
Upper Left Upper Right Booklet Booklet Stitch
Notes
•“Booklet” and “Booklet Stitch” cannot be selected when Finisher is installed. “Upper Left” or “Upper Right” should be selected according
to the orientation of the paper set in the cassette. If either “Upper Left” or “Upper Right” is selected, a message will be displayed in order
to verify the orientation of the paper.
•“Multi Tray” and “Folding Unit” can be selected when the Multi Finisher is installed.
•“Multi Tray” and “Folding Unit” cannot be selected when the Finisher is installed.
• In order to staple in the lower left or lower right of the paper, select “Rotated” as the “Orientation” setting in the “Media” Tab.
■ Offset
This mode groups prints made from multiple originals and ejects them each one slightly shifted from the precious one.
Offsetting is possible if the optional finisher is installed.
* The following settings are required before Offsetting is possible:
(1) “Device Options” setting in the “Device Settings” Ta b
• Select [Finisher] or [Multi Finisher].
(2) “Output” Ta b
• When the Finisher is installed, select [Tray A (Face-down)] as the “Output to” setting.
• When the Multi Finisher is installed, select [Tray A (Face-down)] or [Tray B (Face-down)] as the “Output to” setting.
• When the Multi Tray is installed, select [Tray 1,2,3,4,5 (Face-down)] as the “Output to” setting.
• Put a check mark in the checkbox for [Offset].
■ Punch
When the optional Finisher is equipped with a Punch Unit, it is possible to have holes punched into the finished copies.
* In order to use the Hole Punch function, it is first necessary to perform the following settings.
(1) “Installable Options” setting in the “Device Settings” Ta b
Select [Multi Finisher] and select the type of Punch Unit. For more details on how to select the Punch Unit, refer to “Punch Unit” on
page 2-15.
(2) In the “Output” Ta b
• When the Multi Finisher is installed, select [Tray A (xxxx)] or [Tray B (xxxx)] as the “Output to” setting.
• When the Multi Tray is installed, select [Tray 1,2,3,4,5 (xxxx)] as the “Output to” setting.
• Put a check mark in the checkbox for [Punch] and select the type of hole punching you want to perform.
• When [Punch] is selected, [...]box is displayed. Click on [...] box and select the position (Left, Right, Upper) of the hole punching
you want to perform.
Note
The Staple and Offset functions cannot be used when selected [xxxx (Face-up)] as [Output to] setting.
■ Job Settings...
Clicking on the [Job Settings...] button opens up the [Job Settings] dialog box from which you can print out using the e-MPS (Job Storage)
function. For details, see “2-6-1 Printing using the e-MPS function” on page 2-11.
To Next Page
Loading...
