Labconco Purifier Logic+ 30231 Series

Questions and Answers

M
Marie JamesAug 7, 2025
Why is the fluorescent light not working on my Labconco Laboratory Equipment?
- M
  mollyswansonAug 7, 2025
  The fluorescent light might not be working due to several reasons: * The sash is closed: Open the sash, as the fluorescent lights are designed not to function when the sash is closed. * Defective lamp(s): Replace the defective lamp(s). * Disconnected lamp wiring: Inspect the lamp wiring. * Defective lamp ballasts: Replace the lamp ballasts. * Keypad issues: Run keypad diagnostics and check connections if the keypad is disconnected or defective.
F
fjohnsonAug 12, 2025
What to do if the UV light is not working on my Labconco Laboratory Equipment?
- B
  bmorrisAug 12, 2025
  If the UV light is not working, here are a few things to check: * Sash position: Ensure the sash is closed, as the UV light will not operate when the sash is open. * Lamp condition: Replace the lamp if it's defective. * Wiring: Inspect the lamp wiring for any disconnections. * Ballast: Replace the lamp ballast if it's defective. * Keypad: Run keypad diagnostics and check connections.
L
Leslie JacksonAug 25, 2025
How to fix dim or flickering fluorescent light in Labconco Purifier Logic+ 30231 Laboratory Equipment?
- S
  sanderskristenAug 25, 2025
  If the fluorescent light is dim or flickering, it could be due to: * Defective lamp(s): Replace the defective lamp(s). * Lamp wiring issues: Inspect the lamp wiring. * Defective lamp ballast: Replace the lamp ballast.
S
Samantha MillerAug 31, 2025
What to do if the UV light is dim or flickering in my Labconco Purifier Logic+ 30231 Laboratory Equipment?
- T
  Tammy WellsAug 31, 2025
  If the UV light is dim or flickering, consider the following: * Lamp condition: Replace the lamp if it is defective or at the end of its operating lifetime. * Wiring: Inspect the lamp wiring for any disconnections. * Ballast: Replace the lamp ballast if it's defective.
C
chavezrobertNov 17, 2025
Why is the Airflow Alert going off on my Labconco Laboratory Equipment?
- M
  Maria GomezNov 17, 2025
  The Airflow Alert may be triggered, and/or you might notice a slight decrease in the filter life remaining gauge due to several factors: * HEPA filter loading: The gauge reading steadily decreases as the cabinet is used. * Blockage of the return air slots or grille: Check all return air slots and grilles to ensure that they are not blocked or restricted. * Blockage of the exhaust outlet: Ensure that the exhaust outlet is not blocked or restricted. * Blockage or restriction under the work surface: Ensure that the towel catch and plenum beneath the work surface are unobstructed. * Contamination of work in the cabinet: See 'Use of the cabinet' section in the manual. * Restriction of the return air slots or grille – blockage of the exhaust outlet: Ensure that all return air slots,...

Summary

Introduction

Prerequisites

Space Requirements

Details the necessary space and dimensions for cabinet installation.

Clearance

Specifies the minimum recommended clearance around the cabinet for service.

Location Requirements

Provides guidance on optimal placement to ensure proper airflow and operation.

Exhaust Requirements

Outlines requirements for connecting the cabinet to an exhaust system.

Electrical Requirements

Lists the electrical specifications, including voltage and amperage for models.

Service Line Requirements

Details the specifications for connecting utility service lines to the cabinet.

Getting Started

Unpacking and Initial Setup

Instructions for carefully removing the cabinet from packaging and checking for damage.

Cabinet Installation and Mounting

Covers installing the cabinet on existing surfaces or Labconco base stands and stand options.

Utility Connections

Guides on connecting service lines, exhaust, and cable portals.

Drain Valve and Initial Certification

Procedures for drain valve installation and the importance of initial cabinet certification.

Performance Features and Safety Precautions

Filter Performance (HEPA;ULPA)

Explains the function and efficiency of HEPA and ULPA filters in particulate removal.

Airflow Dynamics

Details laminar and directional airflow critical for cabinet performance and containment.

Cabinet Components and Controls

Discusses motor, blower, air intakes, and the UV lamp's function.

General Safety Precautions

Critical safety guidelines for operating and maintaining the biosafety cabinet.

Using the Cabinet

System Controls and Information

Covers system reset, info display, and alarm conditions.

Sash Operation and Startup

Instructions for sash movement, starting the blower, and lights.

Touchpad Interface and Menu Navigation

Details the touchpad layout and navigating system menus.

Cabinet Configuration and Settings

Guides on MyLogic, settings, UV lamp, and timer operations.

Working in the Biosafety Cabinet

Comprehensive guide on planning, techniques, loading, and shutdown.

Maintaining the Cabinet

Routine Maintenance Schedule

Outlines daily, weekly, and monthly maintenance tasks for peak performance.

Service Operations: Component Removal

Procedures for removing and reinstalling work surface, grilles, and panels.

Lamp Replacement and Breaker Reset

Instructions for changing lamps and resetting circuit breakers.

Storage Procedures

Guidelines for preparing the cabinet for extended periods of non-use.

Troubleshooting

Common Problems and Solutions

Lists common operational problems, their causes, and corrective actions.

Appendix A: Components

Replacement Parts List

Lists part numbers and descriptions for replacement components and accessories.

Appendix B: Dimensions

Appendix C: Specifications

Electrical and Motor Specifications

Details electrical requirements and motor specifications for various cabinet models.

Environmental Conditions

Lists acceptable ambient temperature, humidity, and voltage conditions for operation.

Appendix D: Accessories

Appendix E: Quick Chart

Labconco Purifier Logic+ 30231 Series Specifications

General

Type	Class II, Type A2 Biological Safety Cabinet
Inflow Velocity	100 FPM
Filter Type	HEPA
Electrical Requirements	115V, 60 Hz, 8.0A
UV Light	Optional
Construction	Stainless Steel
Nominal Width	3 ft
Work Area Depth	30 in
Exhaust HEPA Filter	99.99% efficient on particles 0.3 micron
Motor	ECM motor
Certifications	NSF/ANSI 49
Supply HEPA Filter	99.99% efficient at 0.3 microns