Lenze 4800 - Page 220

Configuration
7-129
48XX/49XXSHB0399
Code Possible settingsNameCode
InfoSelectionLenze
Name
[C111*] Signal for C110
-0- No signal
-1- Main setpoint (C046), reference: n
max
-2- Input ramp function generator, reference:
n
max
-3- Output ramp function generator, reference:
n
max
-4- Additional setpoint (C049), reference: n
max
-5- n
set
at n-controller input (C050), reference:
n
max
Armature setting range: 100 % M
max
correspond to 100 % I
max
(C022, C023)
The actual armature current I
act
(C054) is
standardized, according to the controller:
I
act
X4/62, X8 Type
X4/63
16A 4.4V 110kHz 4902
25A 4.7V 118kHz 4903
55
A
4.8
V
120
k
H
z
4904
-6- n
act
(C051), reference: n
max
(X4/63)
-8- n
act
(C382), reference: n
max
(X8)
-20- n-controller output, reference: M
max
-21- M
set
(C047), reference: M
max
-22- I
set
(C063), reference: I
max
(C022, C023),
(X4/62)
5
5
A
4
.
8
V
1
2
0
k
H
z
4
9
0
4
110A 4.9V 122kHz 4905
200A 6.4V 159kHz 4906
250A 4.4V 110kHz 4907
330A 5.2V 129kHz 4X08
500A 5.8V 144kHz 4X09
7
0
0
A
5
.
8
V
1
4
4
k
H
z
4
X
1
1
-23- I
act
(C054), reference: (see ’Info’)
-25- M
set
(C056), reference: M
max
-28- I¼t load, reference: 100%
-29- I
2
¼t load, reference: 100%
-30- V
A
(C052), reference: 1000 V
7
0
0
A
5
.
8
V
1
4
4
k
H
z
4
X
1
1
1000A 5.8V 146kHz 4X12
1200A 7.0V 175kHz 4X13
With C111 = -5- the selection depends on
the configuration set under C005.
I
f
C
0
0
5
6
X
7
2
t
h
i
l
C
1
1
1
-35- Mains frequency, reference: 30Hz = 0V,
70Hz = 10V
-40- Fiel current setpoint, reference: max.
controller field current I
Fmax
-41- Actual field current, reference: I
Fmax
-60- Output motor potentiometer, reference:
100%
If C005 = -6X-, -72- the signal C111 =
-5- outputs the corresponding input pulse
current.
-61- Output process controller, reference: 100%
-62- Output arithmetic block 2, reference: 100%
-63- Digital frequency input X5, reference: 100%
-64- Digital frequency input X9, reference: 100%
-65- Resolver, reference: 100%
-66- Digital / analog conversion 1 (C272),
reference: 100%
-67- Digital / analog conversion 2 (C273),
reference: 100%
-68- Motor power, reference: 5 V = P
rated
-69- Motor torque, reference: 5 V = M
rated
-70- Output dead band element, reference: 100%
-71- Output DT1 element, reference: 100%
-72- Output absolute value generator, reference:
100%
-73- Output limiting element 1, reference: 100%
-74- Output PT1 element, reference: 100%
-75- Output arith.-block 3, reference: 100%
-76- Output add.-block 1, reference: 100%
-77- Output add.-block 2, reference: 100%
-78- Output limiting element 2, reference: 100%
Show/Hide Bookmarks