models 45, 86, 132
moving 11, 12, 258, 260
selecting a location 11, 12
shipping 260
printer control panel
adjusting brightness 80
factory defaults,
restoring 81, 127, 174
indicator light 48, 88, 134
parts 47, 88, 134
Sleep button light 48, 88, 134
using 47, 88, 134
printer control panel, virtual
display
using the Embedded Web
Server 74, 120
printer hard disk
disposing of 82, 128, 175
encrypting 84, 130, 177
installing 24
removing 29
wiping 84, 129, 177
printer hard disk
encryption 84, 130, 177
printer hard disk memory
erasing 84, 129, 177
printer information
where to find 9
printer is printing blank pages 327
printer messages
[x]‑page jam, clear manual feeder.
[250] 273
[x]‑page jam, lift front cover to
remove cartridge. [200–
201] 265
[x]‑page jam, open tray [x].
[24x] 272
[x]‑page jam, open upper and
lower rear door. [231–234] 269
[x]‑page jam, open upper rear
door. [202] 268
[x]‑page jam, remove paper, open
expander rear door. Leave paper
in bin. [43y.xx] 281
[x]‑page jam, remove paper, open
finisher rear door. Leave paper in
bin. [451] 278
[x]‑page jam, remove paper, open
mailbox rear door. Leave paper
in bin. [41y.xx] 279
[x]‑page jam, remove paper, open
stapler door. Leave paper in bin.
[455–457] 274
[x]‑page jam, remove standard bin
jam. [203] 271
[x]‑page jam, remove tray 1 to
clear duplex. [235–239] 271
Cartridge low [88.xy] 283
Cartridge nearly low [88.xy] 283
Cartridge very low [88.xy] 283
Cartridge, imaging unit mismatch
[41.xy] 283
Change [paper source] to [custom
string] 283
Change [paper source] to [custom
string] load [orientation] 284
Change [paper source] to [custom
type name] 284
Change [paper source] to [custom
type name] load
[orientation] 284
Change [paper source] to [paper
size] load [orientation] 284
Change [paper source] to [paper
type] [paper size] 284
Change [paper source] to [paper
type] [paper size] load
[orientation] 285
Check tray [x] connection 285
Close door or insert cartridge 285
Close finisher side door 285
Close front door 285
Complex page, some data may not
have printed [39] 286
Configuration change, some held
jobs were not restored [57] 286
Defective flash detected [51] 286
Disk corrupted 286
Disk full [62] 286
Disk near full. Securely clearing
disk space. 287
Empty the hole punch box 287
Error reading USB drive. Remove
USB. 287
Error reading USB hub. Remove
hub. 287
Fuser kit early wear warning
[81.xx] 287
Fuser kit near end of life
[81.xx] 287
Imaging unit low [84.xy] 287
Imaging unit nearly low
[84.xy] 288
Imaging unit very low [84.xy] 288
Incompatible output bin [x]
[59] 288
Incompatible tray [x] [59] 288
Incorrect paper size, open [paper
source] [34] 288
Insert hole punch box 289
Insert staple cartridge 289
Insert Tray [x] 289
Install bin [x] 289
Install Tray [x] 289
Insufficient memory for Flash
Memory Defragment operation
[37] 290
Insufficient memory to collate job
[37] 290
Insufficient memory to support
Resource Save feature [35] 290
Insufficient memory, some Held
Jobs were deleted [37] 290
Insufficient memory, some held
jobs will not be restored
[37] 290
Load [paper source] with [custom
string] [paper orientation] 291
Load [paper source] with [custom
type name] [paper
orientation] 291
Load [paper source] with [paper
size] [paper orientation] 291
Load [paper source] with [paper
type] [paper size] [paper
orientation] 292
Load manual feeder with [custom
string] [paper orientation] 292
Load manual feeder with [custom
type name] [paper
orientation] 292
Load manual feeder with [paper
size] [paper orientation] 292
Load manual feeder with [paper
type] [paper size] [paper
orientation] 293
Load staples 291
Maintenance kit low [80.xy] 293
Maintenance kit nearly low
[80.xy] 293
Maintenance kit very low
[80.xy] 293
Memory full [38] 293
Index 360
To Next Page
Loading...
