Lexmark T522 - While Exiting to the Output bin

To Next Page

To Previous Page

While exiting to the output bin

Pull the paper straight out.

If the paper does not move immediately when you pull, stop pulling. Open the upper front door and pull

the paper out.

Main Page

Default Chapter3
- Table of Contents3
Chapter 1: Printer Overview9
Chapter 2: Using the Operator Panel10
- Understanding the Operator Panel10
- Using the Operator Panel Buttons11
- Using the Operator Panel to Change Printer Settings12
- Printing the Menu Settings Page13
Chapter 3: Using the Print and Hold Function14
- Printing and Deleting Held Jobs14
- Accessing Held Jobs from the Operator Panel15
- Recognizing When Format Errors Occur15
- Repeat Print16
- Reserve Print16
- Verify Print16
- Confidential Jobs16
Chapter 4: Canceling a Print Job18
Chapter 5: Printing Folio and Statement Size Paper19
Chapter 6: Choosing Print Material20
- Paper Characteristics20
- Recommended Paper21
- Unacceptable Paper22
- Choosing Preprinted Forms and Letterhead22
- Choosing Prepunched Paper22
- Choosing Paper23
- Choosing Envelopes24
- Choosing Labels24
- Choosing Card Stock25
- Choosing Transparencies26
Chapter 7: Print Material Specifications27
Chapter 8: Loading Print Material31
Chapter 9: Loading a Paper Tray32
- Loading Letterhead33
Chapter 10: Loading the Multipurpose Feeder34
- Capacity34
- Paper Dimensions34
- Trouble-Free Printing34
- Closing the Multipurpose Feeder41
Chapter 11: Loading the Envelope Feeder42
Chapter 12: Loading the 2000-Sheet Drawer46
Chapter 13: Storing Paper47
Chapter 14: Tray Linking48
Chapter 15: Tips for Avoiding Paper Jams49
Chapter 16: Replacing the Print Cartridge50
Chapter 17: Replacing the Charge Roll51
Chapter 18: Replacing the Transfer Roll52
Chapter 19: Replacing the Fuser Assembly53
Chapter 20: Resetting the Maintenance Counter54
Chapter 21: Ordering Supplies55
- Maintenance Kit55
- Print Cartridges55
- Label Fuser Cleaner55
- Charge Roll55
- Transfer Roll56
- Fuser Assembly56
Chapter 22: Storing Supplies57
Chapter 23: Checking an Unresponsive Printer58
Chapter 24: Clearing Paper Jams59
- Identifying Paper Jam Areas59
- Accessing Paper Jam Areas61
- 200 And 201 Paper Jam61
- Remove Cartridge61
- 202 Paper Jam62
- Open Rear Door62
  - Before Reaching the Output bin63
  - While Exiting to the Output bin64
- Paper Jam Check Duplex65
- Paper Jam Check Tray X68
- Paper Jam Check MP Feeder73
- 250 Paper Jam73
- Check Env Feeder73
  - At Entry into the Envelope Feeder73
  - Between the Envelope Feeder and the Printer74
Chapter 25: Solving Display Problems76
Chapter 26: Solving Printing Problems77
Chapter 27: Solving Print Quality Problems79
Chapter 28: Solving Option Problems82
Chapter 29: Solving Network Printing Problems84
Chapter 30: Resolving Other Problems and Questions85
Chapter 31: Understanding Printer Messages86
- Check <Device> Connection90
- Clearing Job Accounting Stat90
- Deleting Jobs91
- Disabling Menus92
- Disk Recovery93
- Enabling Menus93
- Enter Pin93
- Held Jobs May be Lost95
Chapter 32: Using Printer Menus118
Chapter 33: Finishing Menu121
- Duplex Bind123
- Separator Sheets125
- Separator Source126
Chapter 34: Infrared Menu127
- Job Buffering128
- Npa Mode129
Chapter 35: Job Menu132
- Confidential Job133
- Held Jobs133
- Reset Printer134
Chapter 36: Localtalk Menu135
- Localtalk Addr136
- Localtalk Buffer136
- Localtalk Zone137
- Npa Hosts137
Chapter 37: Network Menu139
- Network Buffer140
Chapter 38: Paper Menu143
- Custom Types144
- Envelope Enhance144
- Paper Loading145
- Paper Size146
- Paper Texture147
- Paper Type148
- Paper Weight149
- Substitute Size149
- Universal Setup150
Chapter 39: PCL Emul Menu151
- Auto Cr after Lf152
- Auto Lf after Cr152
- Font Name152
- Font Source153
- Point Size154
- Symbol Set155
Chapter 40: Parallel Menu156
- Advanced Status156
- Honor Init157
- Parallel Buffer158
- Parallel Mode 1158
- Parallel Mode 2158
Chapter 41: Postscript Menu161
Chapter 42: Quality Menu162
- Print Resolution163
- Toner Darkness163
Chapter 43: Serial Menu164
- Data Bits165
- Robust Xon168
- Serial Protocol169
Chapter 44: Setup Menu170
- Auto Continue170
- Download Target170
- Display Language171
- Jam Recovery172
- Job Accounting172
- Page Protect172
- Power Saver173
- Print Timeout173
- Printer Language174
- Resource Save174
- Wait Timeout175
Chapter 45: Utilities Menu176
- Defragment Flash176
- Factory Defaults177
- Format Disk177
- Format Flash177
- Hex Trace178
- Print Directory178
- Print Fonts178
- Job Acct Stat178
- Print Menus179
Chapter 46: USB Menu180
- Usb Buffer182
Chapter 47: Disabling Operator Panel Menus183
Chapter 48: Removing Options184
Chapter 49: Removing the Envelope Feeder185
Chapter 50: Removing a Paper Tray or Duplex Unit187
Chapter 51: Removing Printer or Flash Memory189
Chapter 52: Removing an Option Card190
Chapter 53: Understanding Fonts191
- Typefaces and Fonts191
  - Weight and Style191
  - Pitch and Point Size191
- Bitmapped and Scalable Fonts193
- Resident Fonts194
- Symbol Sets199
  - Symbol Sets for PCL 6 Emulation199
- Downloadable Fonts200
- Printing a Font Sample List200
Chapter 54: Printer Specifications201
- Dimensions201
- Duty Cycle201
Notices202
- Edition Notice203
- Trademarks203
- Licensing Notice204
- Safety Information205
- Cautions and Warnings205
- Electronic Emission Notices205
- Energy Star207
- Laser Notices208
  - Laser Advisory Label208
  - Laser Notice208
Index209

Lexmark T522 - While Exiting to the Output bin

Table of Contents

Other manuals for Lexmark T522

Related product manuals