Lexmark T522 - Page 66

To Next Page

To Previous Page

Pull down and out if the paper is in this position.

5 Close the duplex rear door. Make sure it snaps into place.

6 Locate the recessed areas on each side of the duplex front access cover.

7 Slowly pull the duplex front access cover straight out.

Main Page

Default Chapter3
- Table of Contents3
Chapter 1: Printer Overview9
Chapter 2: Using the Operator Panel10
- Understanding the Operator Panel10
- Using the Operator Panel Buttons11
- Using the Operator Panel to Change Printer Settings12
- Printing the Menu Settings Page13
Chapter 3: Using the Print and Hold Function14
- Printing and Deleting Held Jobs14
- Accessing Held Jobs from the Operator Panel15
- Recognizing When Format Errors Occur15
- Repeat Print16
- Reserve Print16
- Verify Print16
- Confidential Jobs16
Chapter 4: Canceling a Print Job18
Chapter 5: Printing Folio and Statement Size Paper19
Chapter 6: Choosing Print Material20
- Paper Characteristics20
- Recommended Paper21
- Unacceptable Paper22
- Choosing Preprinted Forms and Letterhead22
- Choosing Prepunched Paper22
- Choosing Paper23
- Choosing Envelopes24
- Choosing Labels24
- Choosing Card Stock25
- Choosing Transparencies26
Chapter 7: Print Material Specifications27
Chapter 8: Loading Print Material31
Chapter 9: Loading a Paper Tray32
- Loading Letterhead33
Chapter 10: Loading the Multipurpose Feeder34
- Capacity34
- Paper Dimensions34
- Trouble-Free Printing34
- Closing the Multipurpose Feeder41
Chapter 11: Loading the Envelope Feeder42
Chapter 12: Loading the 2000-Sheet Drawer46
Chapter 13: Storing Paper47
Chapter 14: Tray Linking48
Chapter 15: Tips for Avoiding Paper Jams49
Chapter 16: Replacing the Print Cartridge50
Chapter 17: Replacing the Charge Roll51
Chapter 18: Replacing the Transfer Roll52
Chapter 19: Replacing the Fuser Assembly53
Chapter 20: Resetting the Maintenance Counter54
Chapter 21: Ordering Supplies55
- Maintenance Kit55
- Print Cartridges55
- Label Fuser Cleaner55
- Charge Roll55
- Transfer Roll56
- Fuser Assembly56
Chapter 22: Storing Supplies57
Chapter 23: Checking an Unresponsive Printer58
Chapter 24: Clearing Paper Jams59
- Identifying Paper Jam Areas59
- Accessing Paper Jam Areas61
- 200 And 201 Paper Jam61
- Remove Cartridge61
- 202 Paper Jam62
- Open Rear Door62
  - Before Reaching the Output bin63
  - While Exiting to the Output bin64
- Paper Jam Check Duplex65
- Paper Jam Check Tray X68
- Paper Jam Check MP Feeder73
- 250 Paper Jam73
- Check Env Feeder73
  - At Entry into the Envelope Feeder73
  - Between the Envelope Feeder and the Printer74
Chapter 25: Solving Display Problems76
Chapter 26: Solving Printing Problems77
Chapter 27: Solving Print Quality Problems79
Chapter 28: Solving Option Problems82
Chapter 29: Solving Network Printing Problems84
Chapter 30: Resolving Other Problems and Questions85
Chapter 31: Understanding Printer Messages86
- Check <Device> Connection90
- Clearing Job Accounting Stat90
- Deleting Jobs91
- Disabling Menus92
- Disk Recovery93
- Enabling Menus93
- Enter Pin93
- Held Jobs May be Lost95
Chapter 32: Using Printer Menus118
Chapter 33: Finishing Menu121
- Duplex Bind123
- Separator Sheets125
- Separator Source126
Chapter 34: Infrared Menu127
- Job Buffering128
- Npa Mode129
Chapter 35: Job Menu132
- Confidential Job133
- Held Jobs133
- Reset Printer134
Chapter 36: Localtalk Menu135
- Localtalk Addr136
- Localtalk Buffer136
- Localtalk Zone137
- Npa Hosts137
Chapter 37: Network Menu139
- Network Buffer140
Chapter 38: Paper Menu143
- Custom Types144
- Envelope Enhance144
- Paper Loading145
- Paper Size146
- Paper Texture147
- Paper Type148
- Paper Weight149
- Substitute Size149
- Universal Setup150
Chapter 39: PCL Emul Menu151
- Auto Cr after Lf152
- Auto Lf after Cr152
- Font Name152
- Font Source153
- Point Size154
- Symbol Set155
Chapter 40: Parallel Menu156
- Advanced Status156
- Honor Init157
- Parallel Buffer158
- Parallel Mode 1158
- Parallel Mode 2158
Chapter 41: Postscript Menu161
Chapter 42: Quality Menu162
- Print Resolution163
- Toner Darkness163
Chapter 43: Serial Menu164
- Data Bits165
- Robust Xon168
- Serial Protocol169
Chapter 44: Setup Menu170
- Auto Continue170
- Download Target170
- Display Language171
- Jam Recovery172
- Job Accounting172
- Page Protect172
- Power Saver173
- Print Timeout173
- Printer Language174
- Resource Save174
- Wait Timeout175
Chapter 45: Utilities Menu176
- Defragment Flash176
- Factory Defaults177
- Format Disk177
- Format Flash177
- Hex Trace178
- Print Directory178
- Print Fonts178
- Job Acct Stat178
- Print Menus179
Chapter 46: USB Menu180
- Usb Buffer182
Chapter 47: Disabling Operator Panel Menus183
Chapter 48: Removing Options184
Chapter 49: Removing the Envelope Feeder185
Chapter 50: Removing a Paper Tray or Duplex Unit187
Chapter 51: Removing Printer or Flash Memory189
Chapter 52: Removing an Option Card190
Chapter 53: Understanding Fonts191
- Typefaces and Fonts191
  - Weight and Style191
  - Pitch and Point Size191
- Bitmapped and Scalable Fonts193
- Resident Fonts194
- Symbol Sets199
  - Symbol Sets for PCL 6 Emulation199
- Downloadable Fonts200
- Printing a Font Sample List200
Chapter 54: Printer Specifications201
- Dimensions201
- Duty Cycle201
Notices202
- Edition Notice203
- Trademarks203
- Licensing Notice204
- Safety Information205
- Cautions and Warnings205
- Electronic Emission Notices205
- Energy Star207
- Laser Notices208
  - Laser Advisory Label208
  - Laser Notice208
Index209

Lexmark T522 - Page 66

Table of Contents

Other manuals for Lexmark T522

Related product manuals