Page 12 of 295
DECLARATION OF INCORPORATION OF PARTLY
COMPLETED MACHINERY
LINAK A/S
Smedevænget 8
DK - 6430 Nordborg
LINAK A/S hereby declares that LINAK DESKLINE
®
products, characterised by the following models and types:
Control Boxes CBD6S
Linear Actuators DB5, DB6, DB14, LA23, LA31
Lifting Columns DL1A, DL2, DL4S, DL5, DL6, DL7, DL8, DL9, DL10, DL11, DL12, DL14, DL15, DL16, DL17, DL18, DL19, DL20, DL21, BASE1, LC1
Desk Panels DPA, DPB, DPH, DPF, DPG, DPT, DP, DP1CS
Wireless Controls HB10, HB20, RFRL
Accessories BA001, BLE2LIN, CHUSB, DESK Sensor, DF2, Kick & Click, SLS, SMPS, USB2LIN, WiFi2LIN
LINAK A/S hereby declares that
LINAK HOMELINE
®
products, characterised by the following models and types:
Control Boxes CBD6DC
Linear Actuators LA10, LA18, LA40 HOMELINE
Dual Actuators TD4, TD5
Controls BP10, HB10, HC05, HC10, HC20, HC30, HC40
Accessories CP001, CP002, CP003, BLE2DC, BLE2LIN, DC CONNECTOR, LED Light Rail, MD1, SMPS, WiFi2LIN
LINAK A/S hereby declares that
LINAK MEDLINE
®
& CARELINE
®
products, characterised by the following models and types:
Control Boxes CA20, CA30, CA40, CA63, CAL40, CB6, CB6S MK2, CB6P2, CB8, CB9, CBJ-Home, CO53, CO61, CO65, CO71, COL50, OPS, PJ2, PJB4
Linear Actuators LA20, LA23, LA27 MEDLINE CARELINE , LA28, LA29, LA30, LA31 MEDLINE CARELINE, LA34, LA40 MEDLINE CARELINE, LA44
Lifting Columns BL1, LC1, LC3
Controls ABL, ACC, ACK, ACO, ACOM, ACL, DP, DPH, FS, FS3, FPP, HB30, HB70, HB80, HB100, HB190, HB200, HB400, HD80, HL70, HL80
Accessories BA16, BA18, BA19, BA21, BAL40, BAL50, CH01, CHL40, CHL50, MJB2, MJB5 Plus, SLS, Massage Motor, MDI, QLCI2, UBL, UBL2
LINAK A/S hereby declares that
LINAK TECHLINE
®
products, characterised by the following models and types:
Linear Actuators LA12, LA14, LA23, LA25, LA30, LA33, LA35, LA36, LA37
Accessories FMB
Nordborg, 2021-03-22
LINAK A/S
John Kling, B.Sc.E.E.
Certification and Regulatory Affairs
Authorized to compile the relevant technical documentation
comply with the following parts of the Machinery Directive 2006/42/EC, ANNEX I, Essential health and safety requirements relating to the design and construction of machinery:
1.5.1 Electricity supply
The relevant technical documentation is compiled in accordance with part B of Annex VII and this documentation or part hereof will be transmitted by post or electronically to a
reasoned request by the national authorities.
This partly completed machinery must not be put into service until the final machinery into which it is to be incorporated has been declared in
conformity with the provisions of the Machinery Directive 2006/42/EC where appropriate.
To Next Page
Loading...
Need help?
General
