MacDon M200 - Page 41

UNLOADING AND ASSEMBLY
Form 169018 39 Revision C
L1 C x x x
||
SENSOR I NPUT
L2 M x x x
||
HDR HE I GHT SENSOR
L1 C x x x
||
SENSOR I NPUT
L2 M x x x
||
HDR
A
NGLE SENSOR
L1 C x x x
||
SENSOR I NPUT
L2 M x x x
||
2.45
V
FLO
A
TSENSOR
L1 C x x x
||
SENSOR I NPUT
L2 M x x x
||
KN I FE SPEED SENSOR
L1 C x x x
||
SENSOR I NPUT
L2 M x x x
||
REEL SPEED SENSOR
L1 C x x x
||
SENSOR I NPUT
L2 M x x x
||
HYD O I L TEMP SENSOR
L1 C x x x
||
A
CT I
V
A
TE FUNCT IONS?
L2 M x x x
||
NO/ YES FORCE HE
A
DER TYPE?
L1 C x x x
||
A
CT I
V
A
TE FUNCT I ONS?
L2 M x x x
||
HE
A
DER DOWN / UP
L1 C x x x
||
A
CT I
V
A
TE FUNCT I ONS?
L2 M x x x
||
REEL DOWN / UP
L1 C x x x
||
A
CT I
V
A
TE FUNCT I ONS?
L2 M x x x
||
HDR T I LT I N / OUT
L1 C x x x
||
A
CT I
V
A
TE FUNCT I ONS?
L2 M x x x
||
KN I FE DR I
V
EON
L1 C x x x
||
A
CT I
V
A
TE FUNCT I ONS?
L2 M x x x
||
DR
A
PER/
A
UGER ON
L1 C x x x
||
A
CT I
V
A
TE FUNCT I ONS?
L2 M x x x
||
REEL FORE /
A
FT
L1 C x x x
||
A
CT I
V
A
TE FUNCT I ONS?
L2 M x x x
||
DW
A
DR I
V
EON
L1 C x x x
||
A
CT I
V
A
TE HYD PURGE?
L2 M x x x
||
NO / YES
L1 C x x x
||
TO
A
CT I
V
A
TE PURGE
L2 M x x x
||
PRESS
A
ND HOLD
L1 C x x x
||
PURGE CYCLE ST
A
RTED
L2 M x x x
||
PRESS
A
ND HOLD
L1 C x x x
||
PURGE CYCLE ENDED
L2 M x x x
||
L1 C x x x
||
PURGE CYCLE ENDED
L2 M x x x
||
NO E
X
I T YES
L1 C x x x
||
E
X
IT FUNCTION MENU?
L2 M x x x
||
NO / YES HE
A
DER DOWN / UP
L1 C x x x
||
FORCE HE
A
DER TYPE?
L2 M x x x
||
NO/ YES E
X
IT DI
A
GNOST I CS?
L1 C x x x
||
SELECT HE
A
DER TYPE
L2 M x x x
||
DISK HE
A
DER
L2 M x x x
||
SK
A
UGER
L2 M x x x
||
DK
A
UGER
L2 M x x x
||
GR
A
SS SEED
L2 M x x x
||
20 FT SK DR
A
PER
L2 M x x x
||
25 FT SK DR
A
PER
L2 M x x x
||
30 FT SK DR
A
PER
W
L2 M x x x
||
35 FT SK DR
A
PER
L2 M x x x
||
15 FT DK DR
A
PER
L2 M x x x
||
20 FT DK DR
A
PER
L2 M x x x
||
25 FT DK DR
A
PER
L2 M x x x
||
30 FT DK DR
A
PER
L2 M x x x
||
35 FT DK DR
A
PER
L2 M x x x
||
40 FT DK DR
A
PER
L1 C x x x
||
E
X
IT HE
A
DER TYPE?
L2 M x x x
||
NO / YES FORCE HE
A
DER TYPE?
L1 C x x x
||
E
X
IT DI
A
GNOST I CS?
L2 M x x x
||
NO / YES DI
A
GNOST I C MODE ?
ACTIVATE HYD PURGE - This is to allow the operator
to purge the air from a new or changed pump system.
Pressing and holding the right hand "arrow" button
activates a predetermined timed purge cycle.
Releasing pressure on the switch or a completed cycle
(timed out) will jump to the PURGE CYCLE ENDED
menu selection.
The DWA menu selection should only be
available if the DWA INSTALLED? is set to YES.
For diagnostic purposes each header function
can be activated by using the "arrow" keys on the
CDM. When "SELECT" is pressed the program
will go to the next function that can be activated.
PWM OPERATION: If the HAZARD switch is
pressed instead of the TURN SIGNAL switch the
GSL will operate the PWM valve (HAZARD sw
must be held) and the PWM value will reset to
zero when released.
If "NO" then jump to:
If "NO" then jump to:
If a disk header is detected then the nomeclature
should read: DISC DRIVE instead of KNIFE
DRIVE.
If "NO" then jump to:
If a sensor has been disabled "SENSOR" will be
flashing in the area where the input reading
would have been.
If "NO" then jump to:
If "NO" then jump to:
When "SELECT" is pressed the program goes to
the EXIT HEADER TYPE? menu selection.
This allows the operator to select or "force" a
header ID configuration if a "NO HEADER" ID is
being read by the control system. The header
type will revert back to "NO HEADER" every time
the ignition is cycled.