Manitou 150 AETJ - Page 95

Ü
MANDATORY SERVICE - FIRST 50 HOURS
ALSO PERFORM THE MONTHLY MAINTENANCE.
This service must be carried out in the first 50 hours of service.
Ü
MANDATORY SERVICE - FIRST 200 HOURS OR 6 MONTHS
This service must be carried out after approximately the first 200 hours of service or within the 6 months following the start-up
of the platform (whichever occurs first):
FIRST 200 HOURS BEFORE THE FIRST 6 MONTHS
- If the platform has reached the first 200 hours of service before the first 6 months have expired, perform both the
mandatory service and the 200-hour periodic maintenance e
Ü
200H-PERIODIC MAINTENANCE - EVERY 200
HOURS OF SERVICE OR 1 YEAR.
FIRST 6 MONTHS BEFORE THE FIRST 200 HOURS
- If the platform has not completed 200 hours of service in the first 6 months, carry out only the compulsory service.
3 - 7
- CHECK Wheel nut tightening ............................................................................... 3-22
- CHECK Tightening of electrical connections ................................................................. 3-26
- CHECK Basket nut tightening ............................................................................... 3-30
- CHECK Tightening of the fixing screws on the jib rotation cylinder (150AETJ3D (150AETJC3D)).............. 3-30
- CHECK General inspection.................................................................................. 3-12
- CHECK Platform controls ................................................................................... 3-14
- CHECK Secondary protection system SPS- first version "SafeManSystem" (OPTION)........................... 3-20
- CHECK Secondary protection system SPS- second version (OPTION) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-21
- CHECK Wheel nut tightening ............................................................................... 3-22
- CHECK Battery electrolyte specific gravity ................................................................... 3-23
- GREASE Front steering pivots and steering cylinder ring ...................................................... 3-23
- BLEED Battery trays ........................................................................................ 3-24
- CHECK Emergency controls................................................................................. 3-26
- CHECK Tightening of electrical connections ................................................................. 3-26
- GREASE Teeth on crown gear ................................................................................ 3-26
- LUBRICATE Shafts, hubs and cylinder rings ...................................................................... 3-27
- CHECK Basket nut tightening ............................................................................... 3-30
- CHECK Tightening of the fixing screws on the jib rotation cylinder (150AETJ3D (150AETJC3D)).............. 3-30
- CHECK Telescope setting ................................................................................... 3-31
- CHECK Tightening of the fixing screws on the turntable motor............................................... 3-32
- CHECK Counterweight fixing screw tightening .............................................................. 3-32
- CHECK Tightening of the battery fixing screws .............................................................. 3-32
- CHECK Overload alarm ..................................................................................... 3-33
- CHECK Brakes .............................................................................................. 3-34
- CHECK Turntable motor oil level ............................................................................ 3-35
- CHECK Hydraulic hoses..................................................................................... 3-35
- LUBRICATE Telescope........................................................................................... 3-36
- GREASE Crown gear bearings ................................................................................ 3-36
- CHECK Tightening of the fixing screws for the crown gear ................................................... 3-38
- CHECK Clearance of crown gear * ........................................................................... 3-41
- CHECK Condition of cylinders * ............................................................................. 3-41
- CHECK Condition of electric wiring * . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-41
* Consult your dealer.
647536 (26/11/2020) 150 AETJ/AETJ 3D - 150 AETJ C/AETJ C 3D - 170 AETJ L