Why is the Marantz CD Player remote control not working?
The remote control may not be working because: the unit is too far away (move closer and stay within range); there's an obstacle (remove it); the batteries are dead (replace them); strong light is hitting the sensor (avoid strong light); the REMOTE CONTROL switch is on EXT (set it to INT); or the unit is in amplifier mode (press the MODE CD button).
What does 'Empty' mean on the display of my Marantz SA-11S3 CD Player?
“Empty” means there are no playable files for this unit. Check supported formats.
What to do if my Marantz CD Player is playing but there is no sound?
If your Marantz CD Player is running but you're not hearing any sound, check the following: ensure the amplifier and speakers are correctly connected (refer to the amplifier's manual); verify the amplifier is powered on (refer to its manual); make sure the amplifier's function or selector switch is set to the correct input (CD or AUX, depending on your connection, refer to the amplifier's manual); and ensure the amplifier's volume isn't set too low (adjust the volume, refer to the amplifier's manual).
What to do if the disc won't spin in my Marantz SA-11S3?
If the disc isn't rotating in your Marantz CD Player, make sure the power cord is properly plugged in, the unit is turned on, and the disc is correctly placed on the tray with the label facing up.
Why won't my Marantz SA-11S3 play CD-R or CD-RW discs?
Your Marantz CD Player might not play CD-R/CD-RW discs if the disc is upside down (place it correctly) or if the recorded information isn't in a compatible audio format (CD-DA) or the MP3/WMA file wasn't properly recorded (record correct compatible information).
Why does my Marantz SA-11S3 stop playing in the middle of a CD?
If your Marantz CD Player stops during playback, it could be due to a dirty disc (clean it), scratches (discs with many scratches may not play), or warping (badly warped discs may not play).
How to increase the sound volume from PC on Marantz CD Player?
If the sound is too quiet when outputting signals from a PC, turn up the PC volume.
What does “USB OC” mean on my Marantz CD Player display?
The “USB OC” message means the USB memory device is drawing too much power. Use a USB memory device with an operating current less than 1 A. To clear the message, remove the USB device and turn the unit off and on.
Why does my Marantz SA-11S3 CD Player take so long to read my USB drive?
Reading a high-capacity USB memory device can take time, potentially several minutes. Please wait until reading is completed.
What to do if there is no sound from the headphones connected to my Marantz SA-11S3 CD Player?
If you're not hearing sound from the headphones, press the PHONES button to enable the headphone output.
Identifies and explains the buttons and ports on the front of the unit.
Guidance on selecting and connecting audio and data cables.
Instructions for unbalanced analog audio hookups.
Instructions for balanced analog audio hookups.
How to connect digital audio sources via optical or coaxial cables.
Steps for connecting an iPod for playback and control.
General| Type | SACD/CD Player |
|---|---|
| Disc Formats | SACD, CD, CD-R/RW |
| Frequency Response (SACD) | 2 Hz - 50 kHz |
| Frequency Response (CD) | 2 Hz - 20 kHz |
| Signal-to-Noise Ratio (SACD) | 110 dB |
| Signal-to-Noise Ratio (CD) | 110 dB |
| Digital Outputs | Coaxial, Optical |
| Analog Outputs | XLR, RCA |
| Headphone Output | Yes |
| Weight | 14.5 kg |
| Dynamic Range (SACD) | 110 dB |
| Dynamic Range (CD) | 100 dB |
| Power Consumption | 30 W |
| Total Harmonic Distortion (SACD) | 0.0009% |
| Output Level/Voltage | 2.2V |
| Dimensions (W x H x D) | 440 x 129 x 406 mm |
| Digital-to-Analog Converter | CS4398 |
To Next Page
