Marantz SR 8015 - Sound Modes and Surround Parameters

Sound modes and surround parameters
Sound mode
Surround Parameter
Dialog
Enhancer
Tone
※9
Subwoofer
Level Adjust
※ 11
Audyssey
Cinema EQ
Loudness
Management
※2
Dynamic
Compression
※3
Dialog
Control
※4
Low
Frequency
Effects
※5
Speaker
Select
※6
Speaker
Virtualizer
※7
DTS
Neural:X
IMAX
IMAX Audio
Settings
High Pass
Filter
※8
Low Pass
Filter
※8
Subwoofer
Mode
※8
Auro-Matic
3D Preset
Auro-Matic
3D Strength
Auro-3D
Mode
Subwoofer
MultEQ®
XT32
※12※13
Dynamic EQ
※14※15
Dynamic
Volume
※14※15
Audyssey
LFC™
※14※15
M-DAX
※ 16
Bass Sync
※ 17
Direct/Pure Direct (2-channel) ※ 1 ○ ○ ○※ 18 ○※ 18
Direct/Pure Direct (Multi-channel)
※1
○ ○ ○ ○ ○ ○
DSD Direct (2-channel) ○※ 18 ○※ 18
DSD Direct (Multi-channel) ○ ○
Stereo ○ ○ ○ ○ ○※ 19 ○ ○ ○※ 19 ○ ○ ○ ○ ○ ○
Dolby Atmos ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Dolby TrueHD ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Dolby Digital Plus ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Dolby Digital ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Dolby Surround ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
IMAX DTS:X ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
IMAX DTS ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
DTS:X ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
DTS-HD ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
DTS Express ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
DTS 96/24 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
DTS Surround ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
DTS Neural:X ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
DTS Virtual:X ○ ○ ○ ○ ○ ○ ○
Auro-3D ○ ○ ○※ 20 ○※ 20 ○※ 21 ○ ○ ○ ○ ○ ○ ○ ○ ○
Auro-2D Surround ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Multi Ch In ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
MPEG-4 AAC (JP Only) ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
MPEG-2 AAC (JP Only) ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Multi Ch Stereo ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Virtual ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
※ 1 During playback in Pure Direct mode, the surround parameters are the same as in Direct mode.
※ 2 This item can be selected when a Dolby Digital, Dolby Digital Plus, Dolby TrueHD or Dolby Atmos signal is played.
※ 3 This item can be selected when a Dolby Digital, Dolby Digital Plus, Dolby TrueHD, Dolby Atmos, DTS:X or DTS signal is played.
※ 4 This item can be selected when a DTS:X signal that is compatible with the Dialog Control function is input.
※ 5 This item can be selected when a Dolby Digital or DTS signal or DVD-Audio is played.
※ 6 This item can be selected when Height, Ceiling or Dolby Atmos Enabled speakers are used.
※ 7 This item can be set when any Height, Ceiling or Dolby Atmos Enabled speakers are not used, or Surround speakers are not used.
※ 8 This item can be selected when “IMAX Audio Settings” in the menu is set to “Manual”.
※ 9 This item cannot be set when “Dynamic EQ” is set to “On”.
※ 10 This item cannot be set when “Center” is set to “None”.
※ 11 This item cannot be set when “Subwoofer” in the menu is set to “None”.
※ 12 This item cannot be set when Audyssey® Setup (Speaker Calibration) has not been performed.
※ 13 This item cannot be selected when a DTS:X format with a sampling frequency of over 48 kHz is input.
※ 14 This item cannot be set when “MultEQ® XT32” in the menu is set to “Off”.
※ 15 This item cannot be set when sound mode is “DTS Virtual:X” or sound mode that have “+Virtual:X” in the sound mode name.
※ 16 This item can be set when the input signal is analog, PCM 48 kHz or 44.1 kHz.
※ 17 This can be set when the LFE signal is included in the input signal.
※ 18 This setting is available when “Subwoofer Mode” in the menu is set to “LFE+Main”.
※ 19 This item can be set when “Front” is set to “Small” or “Subwoofer Mode” is set to “LFE+Main”.
※ 20 This can be set if the input signal does not contain an Auro-3D signal or if the input Auro-3D signal does not contain Front Height channels.
※ 21 This can be set if the input signal contains an Auro-3D signal.
8
Before Servicing
This Unit
Electrical Mechanical Repair Information Updating