MARS COMMERCE ZEUS4-MC Lite - User Manual

MARS COMMERCE ZEUS4-MC Lite

56 pages

Save Page as PDF

To Next Page

To Next Page

Loading...

ZEUS4-MC Lite

PSTN/GSM/GPRS INTERFACE &

SMS GSM ALARM COMMUNICATOR

INSTALLATION MANUAL

Version Rev.12+: ZEUS4-MC LITE_Manual_2_4 03082015.doc

Table of Contents

Default Chapter2
- Table of Contents2
1 For Your Safety5
2 Introduction6
3 Features and Applications7
4 Start up8
5 Leds9
6 Clear All Programmed Data from Sim10
7 Connecting Diagram11
- Figure 1: Connection Diagram11
8 Description of Terminal Blocks12
9 Programming Options13
10 Zeus4-MC Lite Parameters14
- Security Level14
- Table 1: SL Parameter14
- Table 2: Example SL Parameters14
- Alarm Support15
- Table 3: in Parameters15
- Table 4: in Parameters Example15
- Figure 2: Output Configuration15
- Table 5: ID Parameters16
- Table 6: ID Parameters Example16
- Table 7: DD Parameters16
- Table 8: DD Parameters Example16
- Table 9: TN Parameters17
- Table 10: TN Parameters Example17
- Table 11: LN Parameters18
- Table 12: LN Parameters Example18
- Table 13: MAIN, BATT Parameters19
- Table 14: MAIN, BATT Parameters Example19
- Table 15: os Parameters20
- Table 16: os Parameters Example20
- Table 17: OD Parameters20
- Table 18: OD Parameters Example21
- Table 19: IT, AR and IB Parameters21
- Table 20: IT, AR and IB Parameters Example22
- Table 21: Alarm SMS Formatting22
- Prepaid Card Credit and Validity Information23
- Table 22: ZEUS4-MC LITE DTMF Commands23
- Table 23: Credit Checking Parameters24
- Table 24: Credit Checking Parameters Example24
- Set-Up Parameters25
- Table 25: Set-Up Parameters28
- Table 26: Set-Up Parameters Example29
- Contact ID Event Reporting30
- Table 27: CID Parameters30
- Table 28: CID Parameters Example31
- Event Log Parameters32
- Table 29: LOG Parameters32
- Table 30: LOG Parameters Example32
- Line Interface Configuration33
- Table 31: Line Interface Parameters34
- Table 32: Line Interface Parameters Example34
11 Print-Out of the Parameters35
- Receive All Parameters (Pall)35
- Receive Line Interface Configuration (Pmc)35
- Receive Telephone Numbers (Ptn)35
- Receive Links (Pln)35
- Receive Input Parameters (Pin)35
- Receive Input Filter Value (Pid)35
- Receive Delay before Dial Value (Pdd)36
- Receive Input Filter Parameters (Pif)36
- Receive Credit Check Numbers (Pcn)36
- Receive Credit Check Parse String Paramaters (Pcref)36
- Receive Credit Status for Cc1 (Pcc1)36
- Receive Credit Status for Cc2 (Pcc2)36
- Receive Credit Status for Cc3 (Pcc3)37
- Receive Access Telephone Numbers (Psl)37
- Receive Output Parameters (Pos)37
- Receive Link for Local Alarm Output (Pod)37
- Receive All Programmed Sms Messages (P#)37
- Receive the Power Level on the Unit (Ppwr)37
- Receive Set-Up Parameters Value (Ppa)37
- State of the Credit for the Prepaid Card38
- Receive CID Parameters (Pcid)38
- Receive Log Parameters and Events (Plog)38
- State of the Outputs (Porc)38
- State of the Inputs (Ins)38
- Receive System Status (Psys)38
12 System Commands39
- Factory Default Command (Sdclr)39
- Gsm Module Restart (Mres)39
- System Restart (Ssres)39
- Log Memory Clear (Lclr)39
13 Checking and Changing System Status (On/Off)40
- Checking System Status by Sms Command40
- Changing System Status to on (System On)40
- Changing System Status to off (System Off)40
14 Checking the Input Status41
- Checking Input Status by Sms Command41
15 Checking and Changing Outputs42
- Checking Output Status by Sms Command42
- Output Remote Control by Sms Command42
16 Changing Parameters Using the Sms Command43
17 Configuration Examples44
- Alarm Configuration44
- CID Event Reporting44
18 Gprs-Tcp/Ip Connection - Basics45
19 Gprs-Tcp/Ip Configuration46
- Ipen46
- Ipcid46
- Ipapn46
- Ipusr46
- Ippsw46
- Ipadd147
- Ipadd247
- Ipport47
- Ipdns147
- Ipdns247
- Ipmod48
- Ippr48
- Ipcre48
- Pip48
20 Gprs-Tcp/Ip Connection49
- General Configuration49
- Event Reporting49
- Table 33: Mandatory GPRS-TCP/IP Connection Parameters49
- Table 34: Usually Needed GPRS-TCP/IP Connection Parameters49
- Table 35: Event Reporting Parameters49
- Ip Management50
- Table 36: IP Management Parameters50
21 Gprs-Tcp/Ip Example51
22 Technical Specification52
23 Default Settings on Zeus4-MC Lite53
- Table 33: ZEUS4-MC LITE Default Settings55
24 Contacts56

Need help?

Do you have a question about the MARS COMMERCE ZEUS4-MC Lite and is the answer not in the manual?

Summary

FOR YOUR SAFETY

START UP

CLEAR ALL PROGRAMMED DATA FROM SIM

CONNECTING DIAGRAM

DESCRIPTION OF TERMINAL BLOCKS

PROGRAMMING OPTIONS

ZEUS4-MC LITE PARAMETERS

SECURITY LEVEL

Defines access levels for programming and remote control via phone book entries.

ALARM SUPPORT

Manages alarm reporting capabilities, including input and output configurations.

PREPAID CARD CREDIT AND VALIDITY INFORMATION

Manages prepaid SIM card credit limits and validity period for warning SMS.

SET-UP PARAMETERS

Configures various operational parameters like language, LEDs, and timers.

CONTACT ID EVENT REPORTING

Supports sending events in Contact ID format to CMS.

EVENT LOG PARAMETERS

LINE INTERFACE CONFIGURATION

Configures special functions related to the POTS interface.

SYSTEM COMMANDS

FACTORY DEFAULT COMMAND (SDCLR)

Resets the system to factory default settings and restarts.

GSM MODULE RESTART (MRES)

Restarts the GSM module of the device.

SYSTEM RESTART (SSRES)

Restarts the entire ZEUS4-MC LITE system.

LOG MEMORY CLEAR (LCLR)

CHECKING AND CHANGING SYSTEM STATUS (ON;OFF)

CHECKING SYSTEM STATUS BY SMS COMMAND

Checks the system's current ON/OFF state via SMS.

CHANGING SYSTEM STATUS TO ON (SYSTEM ON)

Switches the system to the ON state via SMS command.

CHANGING SYSTEM STATUS TO OFF (SYSTEM OFF)

Switches the system to the OFF state via SMS command.

CHECKING THE INPUT STATUS

CHECKING INPUT STATUS BY SMS COMMAND

CHECKING AND CHANGING OUTPUTS

CHECKING OUTPUT STATUS BY SMS COMMAND

OUTPUT REMOTE CONTROL BY SMS COMMAND

CHANGING PARAMETERS USING THE SMS COMMAND

GPRS-TCP;IP CONNECTION - BASICS

GPRS-TCP;IP CONFIGURATION

IPEN

Enables or disables the GPRS-TCP/IP connection.

IPCID

Enables sending local and Ademco Contact ID events over GPRS-TCP/IP.

IPAPN

Sets the Access Point Name for GPRS-TCP/IP connection.

IPUSR

Sets the username for GPRS-TCP/IP connection.

IPPSW

Sets the password for GPRS-TCP/IP connection.

IPADD1

Sets the primary IP address of the GPRS-TCP/IP server.

IPADD2

IPPORT

IPMOD

IPPR

IPCRE

GPRS-TCP;IP CONNECTION

GENERAL CONFIGURATION

EVENT REPORTING

IP MANAGEMENT

DEFAULT SETTINGS ON ZEUS4-MC LITE

MARS COMMERCE ZEUS4-MC Lite Specifications

General

Brand	MARS COMMERCE
Model	ZEUS4-MC Lite
Category	Security System
Language	English