Maytronics Dolphin Wave - Troubleshooting

17
Troubleshooting
How to save log file to USB memory stick (incase required by technician):
From the main screen (with the "Wave" logo), press on the green button in sequence –
'right-left-right-left' and follow the further instructions.
Error Message Check Action to Take
Imp over load Is there dirt or other
foreign matter in the
impeller?
Unscrew the bolt that secures the protective
cover of the impeller. Turn it counter-
clockwise slightly, until it is released.
Remove any dirt around the impeller.
Replace the protective cover.
Imp over load Does the problem re-
occur on every
operation?
Contact the Maytronics dealer/distributor.
Imp under load Does the problem re-
occur on every
operation?
Contact the Maytronics dealer/distributor.
Drive over load Is there any interfering
dirt in the driving
belts, brushes, or drive
axles?
Remove any dirt or foreign bodies that might
have become entangled with the driving
belts, brushes, or drive axles.
Drive over load Does the problem re-
occur on every
operation?
Contact the Maytronics dealer/distributor.
Drive under load Does the problem re-
occur on every
operation?
Contact the Maytronics dealer/distributor.
DC input 1. Is there an
electrical short,
partial or complete
disconnection?
2. Is there a visible
rupture in the
floating cable?
Contact the Maytronics dealer/distributor.
Robot got stuck on
pool wall
1. Has the robot
stopped in a
vertical position of
more than 70º?
2. Has the robot stuck
on an obstacle?
Move the robot from its position and remove
the obstacle. Reactivate.
If this re-occurs, contact the Maytronics
dealer/distributor.
Out of water Was the robot operated
out of the water for an
extended time?
1. Check that the impeller is in order and
that its blades are not broken.
2. Reactivate. If this re-occurs, contact
the Maytronics dealer/distributor.
17
Troubleshooting
How to save log file to USB memory stick (incase required by technician):
From the main screen (with the "Wave" logo), press on the green button in sequence –
'right-left-right-left' and follow the further instructions.
Error Message Check Action to Take
Imp over load Is there dirt or other
foreign matter in the
impeller?
Unscrew the bolt that secures the protective
cover of the impeller. Turn it counter-
clockwise slightly, until it is released.
Remove any dirt around the impeller.
Replace the protective cover.
Imp over load Does the problem re-
occur on every
operation?
Contact the Maytronics dealer/distributor.
Imp under load Does the problem re-
occur on every
operation?
Contact the Maytronics dealer/distributor.
Drive over load Is there any interfering
dirt in the driving
belts, brushes, or drive
axles?
Remove any dirt or foreign bodies that might
have become entangled with the driving
belts, brushes, or drive axles.
Drive over load Does the problem re-
occur on every
operation?
Contact the Maytronics dealer/distributor.
Drive under load Does the problem re-
occur on every
operation?
Contact the Maytronics dealer/distributor.
DC input 1. Is there an
electrical short,
partial or complete
disconnection?
2. Is there a visible
rupture in the
floating cable?
Contact the Maytronics dealer/distributor.
Robot got stuck on
pool wall
1. Has the robot
stopped in a
vertical position of
more than 70º?
2. Has the robot stuck
on an obstacle?
Move the robot from its position and remove
the obstacle. Reactivate.
If this re-occurs, contact the Maytronics
dealer/distributor.
Out of water Was the robot operated
out of the water for an
extended time?
1. Check that the impeller is in order and
that its blades are not broken.
2. Reactivate. If this re-occurs, contact
the Maytronics dealer/distributor.