MB QUART STAGE 5

To Next Page

To Previous Page

NOTES

Use this section to record serial numbers of each product, nal gain and crossover settings of ampliers

or any other wiring or installation-related details that will be helpful if you need to add on to the system or

troubleshoot any unforeseen issues.

Main Page

Introduction2
What’s Included2
Installation Overview Video2
Warranty2
Technical Support2
Installation Time3
Safety Precautions3
Tools and Supplies Needed3
Confirming Power to Busbar3
Preparation for Installation3
Prepare Kick Panel Compression Horns4
Subwoofer Enclosure & Mounting Clips4
Locate Mounting Clips4
Mount Clips4
Install Subwoofer into Enclosure5
Wiring the Subwoofer5
Secure the Subwoofer to the Enclosure5
Remove & Reinstall the Glove Box Door6
Subwoofer Enclosure Modification6
Identify Metal Studs to be Cut6
Cut off Metal Studs6
Dash Area Disassembly7
Remove Center Hood7
Remove Top of Dash7
Remove the Grab Bar7
Remove Dash Fascia Center Hardware8
Remove Dash Fascia Hardware8
Remove the Glove Box8
Remove Center Shroud9
Remove Full Front Cover Dash Top Assembly9
Remove Dynamics Ecu Bracket* and Pocket Screw10
Remove Lower Pocket and Passenger Side Cubby10
Remove Center Switch Hardware10
Prepare Final Electronics for Dash Removal11
Remove Seats12
Unbolt and Mark Center Console Hardware12
Remove Center Console12
Install Power Harness at Busbar (All Models)13
Lay in Harness - Identify Firewall Grommet13
Cut Opening in Grommet and Run Wiring through13
Complete Busbar Connection13
Amplifier Preparation and Mounting14
Loosen Steering Column Nuts14
Step 2 - Amplifier Mounting14
Step 3 - Mounting Plate Installation14
Set the Ecu and Bracket Back15
Trial Fitting the Dual Amp Plate15
Remove Dual Amp Plate and Flip Over, Remove Ecu Bracket15
Subwoofer Enclosure Mounting (All Models)16
Position and Begin Mounting Subwoofer16
Finish Subwoofer Mounting16
Route Subwoofer Harness16
Amplifier and Speaker Wiring Harness Connections17
Power and Speaker Connectors at Amplifiers17
Route Front Speaker Harness17
Route Rear Speaker Harness17
Rear Speaker Pod Installation18
Test Mount Speaker Pods18
Step 2 - Connect Wiring18
Mounting the Kick Panel Speakers19
Mark Drilling Spots on Fender19
Push Outer Bolts through Fender and Kick Panel19
Step 2 - Drill Holes19
Mount Kick Panels20
Connect Wire Harness into Kick Panels20
Wire the Front Speakers20
Mount the Front Speakers20
Amplifier Settings21
Adjust Two-Channel Amplifier21
Adjust Mono Amplifier21
Source Unit Preparation22
Prepare Mounting Components22
Mount Source Unit Using Bracket22
Move Metal Clip to Source Mount22
Installing the Source Unit23
Run Connections to Source Unit Area23
Make Source Unit Connections23
Secure the Source Unit23
Choose a Location24
Drill Hole24
Mount Adapter24
Connect to Source24
Initial Testing25
Reconnect the Battery25
Turn on Ignition25
Step 3 - Initial Checks25
Fine Tuning26
GAIN Adjustment26
X-OVER Switch26
Frequencies Adjustment26
Final Amplifier Mounting27
Set the Ecu and Bracket Back in Place27
Final Fitting the Dual Amp Plate27
Secure Wiriing Harness27
Vehicle Reassembly28
2018.5 Turbo S and 2019+ RZR Models28
Final Inspection29
Complete Wiring Layout30

MB QUART STAGE 5 - Page 31

Table of Contents

Related product manuals