mectron piezo smart - 13.0 Warranty

30
piezo smart - manual of use and maintenance
31
piezo smart - manual of use and maintenance
Recommended separation distances between portable and mobile RF communications equipment
and the PIEZO SMART
The PIEZO SMART is intended for use in an electromagnetic environment in which radiated RF disturbances
are controlled. The customer or the user of the PIEZO SMART can help prevent electromagnetic interference
by maintaining a minimum distance between portable and mobile RF communications equipment
(transmitters) and the PIEZO SMART as recommended below, according to the maximum output power of the
communications equipment.
Rated maximum
output power of
transmitter “W”
Separation distance according to frequency of transmitter “m”
150 kHz to 80 MHz
d = 1,2 √P
80 MHz to 800 MHz
d = 1,2 √P
800 MHz to 2,5 GHz
d = 2,3 √P
0,01 0,12 0,12 0,23
0,1 0,38 0,38 0,73
1 1,2 1,2 2,3
10 3,8 3,8 7,3
100 12 12 23
For transmitters rated at a maximum output power not listed above, the recommended separation distance d
in metres (m) can be estimated using the equation applicable to the frequency of the transmitter, where P is
the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer.
Note:
(1) At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.
(2) These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and
reflection from structures, objects and people.
13.0 Warranty
Before being placed on the market, all MECTRON equipment undergoes a thorough final check to
ensure that it is are in proper working order.
MECTRON warrant their products, purchased brand-new from authorised MECTRON dealers or
importers, free from material or manufacturing defects for a period of 2 (two) years from the date of
purchase.
Throughout the warranty period, MECTRON undertake to repair (or, at their sole discretion, to
replace) free of charge any parts that, in their opinion, are faulty.
Complete replacement of MECTRON products is excluded.
Mectron cannot accept any liability for direct or incidental damage or personal injury in the following
cases:
- If the equipment is used for purposes other than that for which it is intended.
- If the equipment is not used in accordance with all the instructions and requirements described
in this manual.
- If the wiring system in the room where the equipment is used does not comply with the
applicable standards and appropriate requirements.
- If the wiring system in the room where the equipment is used does not comply with the
applicable standards and appropriate requirements.
- If any assembly operations, extensions, settings, alterations or repairs have been carried out
by personnel not authorised by Mectron.
- If the environmental conditions in which the device is kept and stored do not comply with the
requirements indicated in the chapter on technical specifications.
Accidental damages due to transport, incorrect use or carelessness or to connection to power
supplies other than as envisaged and damage to the signalling lamps, handpieces and all
accessories are excluded from the warranty.
The warranty will no longer apply if the apparatus has been tampered with or repaired by
unauthorised personnel.
WARNING
The warranty is valid only if the warranty slip enclosed with the product has been completed in full
and returned to us or, if appropriate, to your MECTRON dealer or importer within 20 (TWENTY)
DAYS from the date of purchase, as proven by the consignment note/invoice issued by the
dealer / importer.
In order to benefit from the warranty service, the customer must return the apparatus to be repaired
to the MECTRON dealer/importer from which it was purchased, at his own expense.
The apparatus should be returned suitably packed (possibly in its original packing material),
accompanied by all the accessories and by the following information:
a) Owner’s details, including his telephone number.
b) Details of the dealer/importer.
c) Photocopy of the consignment note / purchase invoice of the apparatus issued to the owner
and indicating, in addition to the date, also the name of the apparatus and its serial number.
d) A description of the problem.
Transport and any damages caused during transport are not covered by the warranty.
In the event of failures due to accidents or improper use, or if the warranty has lapsed, repairs to
MECTRON products will be charged on the basis of the actual cost of the materials and labour
required for such repairs.