How to resolve low pump pressure on Millipore Elix 70?
If your Millipore Water Filtration System is showing 'LOW PUMP PRESSURE', try increasing the pump pressure. If the issue continues, contact Millipore SAS for assistance.
How to clear EXCH. ASM UV lamp in XX days message on Millipore Elix 70?
The message 'EXCH. ASM UV LAMP IN XX DAYS' on your Millipore Water Filtration System will disappear after you install a new ASM UV Lamp and reset its software timer.
How to fix QGard TL polisher not in place error on Millipore Water Filtration Systems?
To resolve the 'QGARD TL POLISHER NOT IN PLACE' error on your Millipore Water Filtration System, verify that the QGard TL Polisher is installed with its “TAG” Sensor at the top.
How to fix Progard TL pack not in place error on Millipore Elix 70?
To resolve the 'PROGARD TL PACK NOT IN PLACE' error on your Millipore Water Filtration System, make sure the Progard TL is installed with its “TAG” at the bottom.
What to do if product conductivity is less than mini on Millipore Water Filtration Systems?
If the Millipore Water Filtration System displays 'PRODUCT CONDUCTIVITY < MINI', allow the Elix System to remain in PRODUCTION mode for a few minutes. This will help remove any trapped air in the Resistivity Sensor. For further assistance, contact Millipore SAS.
How to clear EXCH. Progard TL in XX days message on Millipore Elix 70 Water Filtration Systems?
The 'EXCH. PROGARD TL IN XX DAYS' message on your Millipore Water Filtration System will disappear once you install a new Progard TL Pack.
What to do if Millipore Elix 70 Water Filtration Systems says Progard TL pack exhausted?
If your Millipore Water Filtration System displays 'PROGARD TL PACK EXHAUSTED', you should replace the Progard TL pack. Alternatively, you can accept the used-up Progard until a new one becomes available.
How to fix % rejection < setpoint on Millipore Elix 70?
If the Millipore Water Filtration System is showing '% REJECTION < SETPOINT', verify that the RO % Rejection Setpoint is at 92%. Allow the Elix System to run for a few minutes, as this may increase the measured RO % Rejection.
What to do if the Millipore Elix 70 Water Filtration Systems shows a low feed pressure?
If the Millipore Water Filtration System displays 'LOW FEED PRESSURE', first ensure the feedwater supply is turned on. Next, check if the Progard TL Pack is clogged by observing the RO reject water in FLUSH mode. If the water pressure issue is resolved during FLUSH mode, the alarm will automatically reset.
What to do if distilled water conductivity is less than mini on Millipore Elix 70 Water Filtration Systems?
If the Millipore Water Filtration System displays 'DIST WATER CONDUCTIVITY < MINI', keep the loop operating for a few minutes to remove any air that could be trapped in the Resistivity Sensor. If problems persist, contact Millipore SAS for assistance.
Details important safety statements, warnings, and symbols for operating the system.
Provides a table outlining typical maintenance tasks, their frequency, and how to perform them.
Step-by-step instructions for removing the old and installing a new Progard TL pretreatment pack.
Instructions for replacing the UV lamp, noting it is often recommended to be done by a service representative.
Explains both automatic and manual methods for sanitizing the RO cartridges.
Details the process for cleaning RO cartridges, including necessary kits and cleaners.
Step-by-step instructions for replacing the QGard TL1 Polisher Pack.
Classifies and explains the different types of messages displayed by the Elix system.
Lists specific LCD messages, their meanings, and recommended actions for alarms and maintenance.
General| Product Water TOC | < 30 ppb |
|---|---|
| Feed Water Type | Potable water |
| Purification Technology | Reverse Osmosis, Electrodeionization |
| Output Water Type | Type 2 Water |
| Bacteria | <1 CFU/mL |
| Bacteria Retention | >99.9% |
| Particle Retention | >99.9% |
| Power Supply | 50/60 Hz |
| Display | LCD |
| Type | Laboratory Water Purification System |
To Next Page