BeneVision N Series Patient Monitor Operator’s Manual 7
12.2 Entering the 12-Lead Screen .................................................................................................................................................................12 - 1
12.3 Initiating Resting 12-Lead ECG Analysis ............................................................................................................................................12 - 1
12.4 Changing 12-Lead ECG Analysis Settings .........................................................................................................................................12 - 1
12.4.1 Setting the High Frequency Filter ..........................................................................................................................................12 - 1
12.4.2 Setting the Baseline Drift Removal ........................................................................................................................................12 - 2
12.5 Glasgow Resting 12-lead ECG Analysis Algorithm Settings .......................................................................................................12 - 2
12.5.1 Editing Patient Information (For Glasgow Algorithms) .................................................................................................12 - 2
12.5.2 Setting Tachycardia and Bradycardia Thresholds (For Glasgow Algorithms) ........................................................12 - 3
12.5.3 Setting the 12-Lead Interpretation Report (For Glasgow Algorithms) ....................................................................12 - 3
12.6 Saving the 12-Lead Interpretation Report ........................................................................................................................................12 - 3
12.7 Printing the 12-Lead Interpretation Report .....................................................................................................................................12 - 3
12.8 Exiting the ECG 12-Lead Screen ...........................................................................................................................................................12 - 3
13 Monitoring Respiration (Resp) .....................................................................................................................................13 - 1
13.1 Resp Introduction ......................................................................................................................................................................................13 - 1
13.2 Resp Safety Information ..........................................................................................................................................................................13 - 1
13.3 Resp Display .................................................................................................................................................................................................13 - 2
13.4 Preparing for Resp Monitoring .............................................................................................................................................................13 - 2
13.4.1 Preparing the Patient .................................................................................................................................................................13 - 2
13.4.2 Placing the Electrodes ................................................................................................................................................................13 - 3
13.5 Changing Resp Settings ..........................................................................................................................................................................13 - 4
13.5.1 Setting the Resp Alarm Properties ........................................................................................................................................13 - 4
13.5.2 Setting the RR Source .................................................................................................................................................................13 - 4
13.5.3 Choosing the Respiration Lead ...............................................................................................................................................13 - 4
13.5.4 Setting the Resp Waveform Size ............................................................................................................................................13 - 4
13.5.5 Setting the Resp Waveform Speed ........................................................................................................................................13 - 4
13.5.6 Setting the Auto Detection Switch ........................................................................................................................................13 - 5
13.5.7 Adjusting the Resp Waveform Detection Threshold ......................................................................................................13 - 5
13.6 Resp Troubleshooting ..............................................................................................................................................................................13 - 5
14 Monitoring Pulse Oxygen Saturation (SpO
2
) ..............................................................................................................14 - 1
14.1 SpO
2
Introduction ...................................................................................................................................................................................... 14 - 1
14.2 SpO
2
Safety Information .........................................................................................................................................................................14 - 2
14.3 SpO
2
Measurement Limitations ...........................................................................................................................................................14 - 2
14.4 SpO
2
Display ................................................................................................................................................................................................14 - 3
14.5 Preparing for SpO
2
Monitoring .............................................................................................................................................................14 - 3
14.6 Changing the SpO
2
Settings ..................................................................................................................................................................14 - 4
14.6.1 Changing the SpO
2
Alarm Settings .......................................................................................................................................14 - 4
14.6.2 Nellcor Sat-Seconds Alarm Management ...........................................................................................................................14 - 4
14.6.3 Setting the Nellcor SpO
2
Sat-Seconds .................................................................................................................................14 - 5
14.6.4 Changing Sensitivity ...................................................................................................................................................................14 - 5
14.6.5 Showing/Hiding PI ......................................................................................................................................................................14 - 5
14.6.6 Monitoring SpO
2
and NIBP Simultaneously .......................................................................................................................14 - 6
14.6.7 Changing the Sweep Speed of the Pleth Wave ................................................................................................................14 - 6
14.7 Changing the PR Settings .......................................................................................................................................................................14 - 6
14.7.1 Changing the PR Alarm Settings ............................................................................................................................................14 - 6
14.7.2 Changing the QRS Volume .......................................................................................................................................................14 - 6