EasyManua.ls Logo

MINERVA OMEGA C/E 652 - Kontroller Som Ska Göras VID Startproblem; Användarens Arbetsuppgifter

Default Icon
66 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
25
HAM11-001 - rev. 02-08-03-13
Controlli da effettuare nel
caso di mancato avviamento
Se la macchina non parte vericare:
• che il cavo di allacciamento alla rete
elettrica sia correttamente inserito
• che l'interruttore generale della rete
elettrica sia abilitato
• che il connettore della macchina sia
collegato al connettore della pedaliera
o all'altro connettore
• che il coperchio tramoggia sia
perfettamente chiuso
• che il rullo formatore sia montato
correttamente (a battuta)
• che il blocco in polietilene sia montato
correttamente a battuta
• che la vetrina di protezione
antinfortunistica in plexiglass sia
perfettamente chiusa.
Compiti dell'operatore
L'operatore deve sempre controllare:
• che sia presente carne nella
tramoggia; ad esaurimento
alimentarla
• che il ciclo di lavoro sia perfetto
• che siano presenti i foglietti di carta
nel relativo gruppo (opzionale)
• il cambio di formato, le regolazioni e la
pulizia.
Checks to be performed in
case of start-up problems
If the machine does not start, always make
sure that:
• the electric cable is properly
connected to a mains outlet
• the general mains switch is on
• the machine connector is plugged into
either the pedal connector or the other
connector
• If the machine does not start check
that the feed pan cover is properly
closed
• the drum is correctly assembled
(rebated edge)
• the polyethylene block is correctly
assembled (rebated edge)
• the plexiglas safety protection door
is closed.
Operator's tasks
The operator must always perform the
following checks:
• verify that meat is present in the
feeding pan, otherwise add some
• verify that the working cycle is correct
• ensure that paper is present in the
optional paper unit
• change the size, adjust and clean the
machine
Mise en service impossible -
controles a effectuer
Si la machine ne se met pas en marche:
• si le câble d’alimentation sur le secteur
est correctement branché
• si l’interrupteur général du secteur est
activé
• si le connecteur de la machine est
branché au connecteur du pédalier
ou à l’autre connecteur
• · contrôler que le couvercle de la trémie
est parfaitement fermé.
• si le tambour est monté correctement
(en butée)
• si le bloc en polyéthylène est monté
correctement (en butée)
• si le volet en plexiglas de protection
contre les accidents est correctement
fermé
Taches de l'operateur
L’opérateur doit impérativement effectuer
les contrôles suivants :
• présence de la viande dans la trémie,
et alimentation lorsqu’elle est épuisée
• cycle de travail correct
• présence du papier dans le groupe
papier (en option)
• changement de l’empreinte des
hamburgers, réglage et entretien.
Kontrollen wenn die Maschine
nicht anläuft
Wenn die Maschine nicht anläuft, über-
prüfen:
• das Zuleitungskabel richtig an das
Netz angeschlossen ist
• der Hauptnetzschalter eingeschalten
ist
• der Stecker des Fussschalters oder
der andere Stecker an die
Steckverbindung der Maschine
angeschlossen ist
• · ob der Trichterdeckel richtig
geschlossen ist.
• der Zylinder richtig montiert ist (am
Anschlag)
• der Polyäthylenblocks richtig
montiert ist (am Anschlag)
• die Plexiglasschutzvorrichtung
geschlossen ist.
Aufgaben des Bedieners
Der Bediener muss folgende Kontrollen
vornehmen :
• Kontrollieren, dass Fleisch in der
Einfüllwanne ist und nachfüllen;
• Kontrollieren, dass der Arbeitszyklus
richtig abläuft;
• Kontrollieren, dass genügend Papier
in der Zubehörvorrichtung vorhanden
ist;
• Format wechseln, reinigen,
nachstellen.
Kontroller som ska göras vid
startproblem
Kontrollera alltid följande om maskinen
inte startar:
• att elkablarna är rätt anslutna till ett
nätuttag
• att huvudströmbrytaren är påslagen
• att maskinkontakten har satts in i an-
tingen pedalkontakten eller den andra
kontakten
• Om maskinen inte startar, kontrollera
att locket till matningstråget är ordentligt
stängt
• att trumman är rätt hopmonterad (falsad
kant)
• att polyetenblocket är rätt hopmonterat
(falsad kant)
• att skyddsdörren i plexiglas är stängd.
Användarens arbetsuppgifter
Användaren måste alltid kontrollera
följande:
• att det nns kött i matningstråget, an-
nars lägga i tillräckligt
• att arbetscykeln är rätt
• att det nns papper i pappersanord-
ningen (tillval)
• ändra storlek, justera och rengöra ma-
skinen