To Next Page

To Previous Page

Pre-Programmed Modes

12.8.4 How the Panel Works in Mode 8

• Activation of either Z-1 or Z-2 changes Hazard Area 1 state into Alarm. Release Timer 1

is started. NAC-1 turns on at Temporal. Upon the expiration of Release Timer 1, RAC-1

is active. NAC-1 turns on steady.

• Activation of either Z-3 or Z-4 changes Hazard Area 2 state into Alarm. Release Timer 2

is started. NAC-2 turns on at Temporal. Upon expiration of Release Timer 2, RAC-2 is

active. NAC-2 turns on steady.

• Activation of Z-6 turns both NAC-1 and NAC-2 on steady.

• Activation of Z-5 can be indicated on NAC-2, if enabled.

Default Chapter3
- Table of Contents3
1 FCC Notice11
- Notice for All FR-320 Series Built-In Udacts Sold in the U.S.A11
2 Introduction13
- Panel Type13
- Deluge Sprinkler System13
- Pre-Action Sprinkler System13
- Agent Release System13
- Overall Features13
3 Conventions15
- Circuits15
- Zone15
- Display Points15
- Wiring Styles15
4 System Components16
- Main Pre-Action/Deluge and Agent Release Control Panel16
- Figure 1 FR-320 Panel16
- Relay Modules: Six Relays17
- Polarity Reversal/City Tie17
- Smart Relay Module17
- Input Class a Converter: Six Circuits17
- Output Class a Converter: Two Circuits18
- Ancillary Annunciator18
- Active End-Of-Line18
- Additional System Accessories18
5 Mechanical Installation19
- Installing the Enclosure19
- Figure 2 Box Dimensions, Semi-Flush Mounting and Trim Ring19
- BBX-1024DS and BBX-1024DSR Mechanical Installation20
- Figure 3 Flush Trim Detail20
- Figure 4 BBX-1024DS and BBX-1024DSR Installation Instructions and Dimensions21
- Installing the Adder Modules22
- Figure 5 Installation of Adder Modules22
6 Cable and Jumper Connections for Main Board, Core Board and Adder Modules23
- Main Pre-Action/Deluge and Agent Release Control Board23
- Figure 6 Main Control Board Cable Connector and Jumper Settings23
- Connectors and Jumpers on the Main Fire Alarm Board24
- Connectors and Jumpers on the Core Board24
- ICAC-306 Input Class-A Converter Adder Module24
- Figure 7 ICAC-306 Input Class-A Converter Adder Module24
- OCAC-302 Output Class-A Converter Adder Module25
- Relay Adder Module25
- Figure 8 OCAC-302 Output Class-A Converter Adder Module25
- Figure 9 RM-306 Six Relay Adder Module25
- Jumpers26
- Correlations26
- Polarity Reversal and City Tie Module (Model PR-300)26
- Jumper Settings26
- Figure 10 Polarity Reversal and City Tie Module26
7 Field Wiring27
- Main Board Field Wiring27
- Initiating Circuit Wiring27
- Figure 11 Initiating Circuit - Class B or Style B Wiring27
- Table 1 Settings Permitted in CAN/ULCS52727
- Table 7 Settings Permitted in CAN/ULCS52727
- Abort and Manual Release Switch Wiring28
- Figure 12 Initiating Circuit- Class a or Style D Wiring28
- Figure 13 Abort and Manual Release Switch Class B or Style B Wiring28
- Figure 14 Abort and Manual Release Switch Class a or Style D Wiring29
- Indicating Circuit Wiring30
- Figure 15 Indicating Circuit - Class B or Style y Wiring30
- Figure 16 Indicating Circuit -Class a or Style Z Wiring30
- Releasing Circuit Wiring31
- Dialer Wiring (US Only)31
- Figure 17 Releasing Circuit Wiring31
- Figure 18 Dialer Wiring31
- Four-Wire Smoke Detector Wiring32
- Relay Adder Module Wiring32
- Figure 19 Four-Wire Smoke Detector Wiring32
- Figure 20 Relay Per Zone (RM-306) Terminal Connection32
- Polarity Reversal and City Tie Module (PR-300) Wiring33
- Figure 21 Polarity Reversal and City Tie Module Terminal Connection33
- Power Supply Connection34
- Figure 22 Power Supply Connection34
- Table 2 Power Supply Ratings34
- Wiring Tables and Information35
- Four-Wire Smoke Power (Regulated)35
- Table 3 Initiating Circuit Wiring Distances35
- Table 4 Indicating Circuit Wiring Distances35
- Supervised Auxiliary Power (Regulated)36
- Unfiltered Supply (Full Wave Rectified)36
8 System Checkout37
- Before Turning the Power "ON37
- Power-Up Procedure37
- Troubleshooting38
- Table 5 Troubleshooting38
9 Indicators, Controls and Operations39
- Figure 23 LED Indicators and Control Buttons39
- Common LED Indicators40
- AC on40
- Common Alarm40
- Common Trouble40
- Battery Trouble40
- Remote Trouble40
- Ground Fault40
- CPU Fail40
- Abort40
- Released40
- ALM/SUP/TBL/BLDG AUDIBLE SIL (Buzzer Silence)41
- Pre Release41
- Menu Buttons41
- Switches and Common Indicators41
- Zone 1 to Zone 441
- Zone 5 and Zone 641
- Out1 and Out2 (NAC Circuits)42
- Out3 and Out4 (Releasing Circuits)42
- Input Circuits Bypass Switch42
- Output Circuits Bypass Switch42
- Common Controls42
- System Reset Button42
- Signal Silence Button42
- Auxiliary Disconnect Button42
- Lamp Test Button43
- ALM/SUP/TBL/BLDG AUDIBLE SIL Button (Buzzer Silence)43
- Circuit (Zone) Disconnect Buttons43
- Common Relays44
- Circuit Types44
- Initiating (Detection) Circuit Types44
- Non-Verified Alarm44
- Water Flow Alarm (Water Flow Sensors)44
- Non-Latching Supervisory (for Supervisory Circuits)44
- Table 6 Relay Types44
- Latching Supervisory (for Supervisory Devices)45
- Abort Switch45
- Manual Release Switch45
- Indicating (Signal) Circuits Types45
- Silenceable Signal45
- Non-Silenceable Signal45
- Silenceable Strobe45
- Non-Silenceable Strobes45
- Evacuation Codes46
- Figure 24 Evacuation and Alert Codes46
10 Configuration47
- Table 8 Settings Permitted in UL86447
- Using the CFG-300 Tool48
- Entering the Passcode48
- Figure 25 FR-320 Configuration48
- How to Use the Keypad to Program the49
- Table 9 Access Levels49
- Command Menu50
- Figure 26 Command Menu50
- Panel Config (Command-Menu)51
- Command Menu-->Panel Config-->Choose a Mode51
- Command Menu-->Panel Config-->Hazard Config52
- Set Time (Command-Menu)56
- Command Menu-->Panel Config-->Default Config56
- View Event Log (Command-Menu)58
- Print Event Log58
- Clear Event Log (Command-Menu)59
- Dialer Config (Command-Menu)59
- Account Info60
- Telephone Line61
- Report Options62
- Time Parameters63
- Dialer Enable/Disable64
- Test Dialer (Command-Menu)65
- Dialer Test Messages65
- Exit (Command-Menu)66
11 Operating the Panel67
- Panel Operation During Various Hazard States67
- Hazard Idle67
- Hazard Alert (or Equivalently First Alarm in Cross-Zoned Application)67
- Hazard Alarm (Pre-Discharge, or Equivalently Second Alarm in Cross-Zoned Application)67
- Hazard Release68
- General Panel Operation68
12 Pre-Programmed Modes69
- Mode 1: Agent Release, Single Hazard, Cross-Zoned, Combined Release69
- Zone Configuration69
- Hazard Configuration69
- NAC Configuration69
- How the Panel Works in Mode 170
- Mode 2: Agent Release, Single Hazard, Not Cross-Zoned, Combined Release71
- Zone Configuration71
- Hazard Configuration71
- NAC Configuration71
- How the Panel Works in Mode72
- Mode 3: Agent Release, Dual Hazard, Cross-Zoned, Split Release73
- Zone Configuration73
- Hazard Configuration73
- NAC Configuration73
- How the Panel Works in Mode 374
- Mode 4: Agent Release, Dual Hazard, Not Cross-Zoned, Split Release75
- Zone Configuration75
- Hazard Configuration75
- NAC Configuration75
- How the Panel Works in Mode 476
- Mode 5: Pre-Action/Deluge, Single Hazard, Cross-Zoned, Combined Release77
- Zone Configuration77
- Hazard Configuration77
- NAC Configuration77
- How the Panel Works in Mode 577
- Mode 6: Pre-Action/Deluge, Single Hazard, Not Cross-Zoned, Combined Release79
- Zone Configuration79
- Hazard Configuration79
- NAC Configuration79
- How the Panel Works in Mode 679
- Mode 7: Pre-Action/Deluge, Dual Hazard, Cross-Zoned, Split Release80
- Zone Configuration80
- Hazard Configuration80
- NAC Configuration80
- How the Panel Works in Mode 781
- Mode 8: Pre-Action/Deluge, Dual Hazard, Not Cross-Zoned, Split Release82
- Zone Configuration82
- Hazard Configuration82
- NAC Configuration82
- How the Panel Works in Mode 883
- Mode 9: Agent Release, Single Hazard, Cross-Zoned, NYC Abort84
- Zone Configuration84
- Hazard Configuration84
- NAC Configuration84
- How the Panel Works in Mode 985
- Mode 10: Agent Release, Single Hazard, Not Cross-Zoned, Combined Release86
- Zone Configuration86
- Hazard Configuration86
- NAC Configuration86
- How the Panel Works in Mode 1087
- Mode 11: Agent Release, Single Hazard, Cross-Zoned, Combined Release88
- Zone Configuration88
- Hazard Configuration88
- NAC Configuration88
- How the Panel Works in Mode 1189
- Mode 12: Pre-Action/Deluge, Single Hazard, Cross Zoned, Combined Release90
- Hazard Configuration90
- NAC Configuration90
- How the Panel Works in Mode 1291
- Mode 13: Pre-Action/Deluge, Single Hazard, Not Cross Zoned, Combined Release92
- Zone Configuration92
- Hazard Configuration92
- NAC Configuration92
- How the Panel Works in Mode 1392
- Mode 14: Pre-Action/Deluge, Single Hazard, Not Cross Zoned, Combined Release94
- Zone Configuration94
- Hazard Configuration94
- NAC Configuration94
- How the Panel Works in Mode 1495
13 Appendix A: Compatible Receivers96
14 Appendix B: Reporting97
- Ademco Contact-ID97
- Event Codes97
- Security Industries Association SIA-DCS98
- Event Codes98
15 Appendix C: Compatible Solenoids99
16 Appendix D: Compatible Synchronized Modules and Horn/Strobes (UL/ULC)100
- 16.0 Appendix D: Compatible Synchronized Modules and100
- Compatible Bells100
17 Appendix E: Specifications101
- Table 10 FR-320 Series Specifications101
- Table 11 FR-320 System Modules and Annunciators102
18 Appendix F: Power Supply and Battery Calculations104
19 Warranty and Warning Information106
- Limited Warranty108

Brand	Mircom
Model	FA-300-3DR
Category	Control Panel
Language	English

Mircom FA-300-3DR User Manual

Table of Contents

Other manuals for Mircom FA-300-3DR

Questions and Answers:

Mircom FA-300-3DR Specifications

Related product manuals