Mitsubishi Electric MELSERVO-J4 MR-J4 A Series - Status Display Mode

4. STARTUP
4 - 20
4.5.3 Status display mode
The servo status during operation is shown on the 5-digit, 7-segment LED display. Press the "UP" or
"DOWN" button to change display data as desired. When the required data is selected, the corresponding
symbol is displayed. Press the "SET" button to display that data. At only power-on, however, data appears
after the symbol of the status display selected in [Pr. PC36] has been shown for 2 s.
(1) Display transition
After selecting the status display mode with the "MODE" button, pressing the "UP" or "DOWN" button
changes the display as shown below.
࿁↢⽶⩄₸
Ꮻㆶࡄ࡞ࠬ
⚥Ⓧ
ታല⽶⩄₸
ࡇ࡯ࠢ
⽶⩄₸
⍍ᤨ⊒↢
࠻࡞ࠢ
1࿁ォౝ૏⟎(1pulseන૏)
ࠨ࡯ࡏࡕ࡯࠲
࿁ォㅦᐲ
1࿁ォౝ૏⟎(1000pulseන૏)
ḳࠅࡄ࡞ࠬ
ABSࠞ࠙ࡦ࠲
ᜰ઎ࡄ࡞ࠬ
⚥Ⓧ
⽶⩄ᘠᕈࡕ࡯ࡔࡦ࠻
Ყ
ᜰ઎ࡄ࡞ࠬ
๟ᵄᢙ
Უ✢㔚࿶
ࠛࡦࠦ࡯࠳
ౝ᳇󰶘ᐲ
ᢛቯᤨ㑆
⊒ᝄᬌ⍮๟ᵄᢙ
࠲ࡈ࠼࡜ࠗࡉ
࿁ᢙ
࡙࠾࠶࠻
ᶖ⾌㔚ജ
1(1Wන૏)
࡙࠾࠶࠻Ⓧ▚㔚ജ㊂1(1Whන૏)
࡙࠾࠶࠻
ᶖ⾌㔚ജ
2(1kWන૏)
࡙࠾࠶࠻Ⓧ▚㔚ജ㊂2(100kWhන૏)
Უ✢㔚࿶
߳
Ꮻㆶࡄ࡞ࠬ
⚥Ⓧ߳
ࠕ࠽ࡠࠣㅦᐲᜰ઎㔚࿶
ࠕ࠽ࡠࠣㅦᐲ೙㒢㔚࿶
ࠕ࠽ࡠࠣ࠻࡞ࠢ
೙㒢㔚࿶
ࠕ࠽ࡠࠣ࠻࡞ࠢ
ᜰ઎㔚࿶
DOWN
UP
To Bus voltage
Cumulative feedback
pulses
Servo motor speed
Droop pulses
Cumulative
command pulses
Command pulse
frequency
A
nalog speed command voltage
A
nalog speed limit voltage
A
nalog torque limit voltage
A
nalog torque command voltage
Regenerative load ratio
Effective load ratio
Peak load ratio
Instantaneous torque
Within one-revolution
position (1 pulse unit)
Within one-revolution position
(1000 pulse unit)
A
BS counter
Load to motor inertia ratio
Bus voltage
Internal temperature of
encoder
Settling time
Oscillation detection
frequency
Number of tough drives
Unit power consumption 1
(increment of 1 W)
Unit power consumption 2
(increment of 1 kW)
Unit total power consumption 1
(increment of 1 Wh)
Unit total power consumption 2
(increment of 100 kWh)
To Cumulative feedback pulse
To Unit total power consumption 2
(increment of 100 kWh)