Mitsubishi UD8350 User Manual

EN-69
Troubleshooting (continued)
Images are not displayed correctly. (continued)
Problem Solution
Tint in projected
images is incorrect.
• CheckthatCOMPUTERINPUTintheSIGNALmenuiscorrectlyset.(Seepage39.)
• Checkthatthecableconnectedtotheexternaldeviceisn’tbroken.
Different color tint. • When comparing images projected by two projectors, tints in the displayed images may be
different because of variation between their optical components. This is not a malfunction.
• Whencomparingtheimageprojectedbythisprojectorwiththosedisplayedonthe
television or PC monitor, tints in the displayed images may be different because of
difference in the range of color reproducibility. This is not a malfunction.
Only the motion areas
in the images supplied
from the computer
aren’t displayed.
• Thisiscausedbythecomputerbeingused.Contactthemanufacturerofyour
computer.
Projected images are
obscured.
• Matchtheoutputresolutionofyourcomputerwiththeresolutionoftheprojector.
For the method to change the output resolution of the computer, contact the
manufacturer of your computer. (See page 73.)
• Someimagesandtextsappearobscuredduringthekeystoneadjustment.Insuch
cases, use the projector without applying the keystone adjustment. (See page 14.)
• WhenSUPERRESOLUTIONisON,thedisplayedimagemaybeobscured.Setitto
OFF. (See page 44.)
Noise appears around
the image.
• InsomeimagessuchasDVD,noisemayappeararoundtherecordedimage.Inthis
case, decrease the setting value of OVER SCAN of the SIGNAL menu. (See page 39.)
Images of WXGA
signal are not
displayed correctly.
• Makeadjustmentaccordingto“Howtoadjustthecomputerimage”onpage45.
Others
Problem Solution
The exhaust vents
emit warm air.
• Thisaircomesoutaftercoolingtheinsideoftheprojector.Youmayfeelhot,butthis
is not a malfunction.
The menu can’t be
used.
• Themicrocomputersinsidetheprojectormaybewronglyoperatingbecauseofnoise.
 Turn off the main power, wait about 10 minutes, and turn on the main power again.
“TEMPERATURE!!” is
displayed.
• Thisindicationappearswhentheambienttemperatureriseshigh.Whentheambient
temperature stays high, the lamp goes out.
 Eliminate any causes of the rise in the ambient temperature.
• Thisindicationappearswhentheairinletoroutletgrilleisblocked.Whentheyare
kept blocked, the lamp goes out.
 Remove the objects blocking the air inlet or outlet grille.
The mark appears. • This mark appears when ineffective operation is carried out. This isn’t a product malfunction.
The remote control
doesn’t function easily
or at all.
• Checkthatthebatteriesareloadedintheremotecontrolorthebatteriesarenot
weak. (See page 6.)
• Checkthattheremotecontrolsensorisn’texposedtodirectsunlightoruorescent
light. (See page 9.)
• Usetheremotecontrolwithinitsoperationrange.(Seepage9.)
• Usetheremotecontrolatleast10cmawayfromtheprojector.
• CheckthattheCONTROLLERIDmatcheswiththePROJECTORID.(Seepages10
and 60.)
• Checkthattheprojectorisn’tcontrolledbyacontrolpanelorotherdevicethatis
connected to the REMOTE 1 IN terminal. (See page 61.)
• When the terminal cover is attached, remote control may not work properly from
behind the projector.
 Remove the terminal cover.
The buttons on the
projector (except for
the POWER button)
don’t function.
• PASSWORDFUNCTIONintheFEATUREmenuhasbeensettoMENUACCESS to
enable the password lock.
 Cancel the password lock or contact the person in charge of management of the
projector. (See page 56.)
• Checkthattheprojectorisn’tcontrolledbyacontrolpanelorotherdevicethatis
connected to the REMOTE 1 IN terminal. (See page 61.)

Mitsubishi UD8350 Specifications

General

Brand	Mitsubishi
Model	UD8350
Category	Projector
Language	English