Mitsubishi WS - 48313

Questions and Answers

W
William RussellAug 18, 2025
What to do if my Mitsubishi WS - 48313 Projection TV remote control does not work?
- C
  Connie TorresAug 19, 2025
  If your Mitsubishi Projection TV remote control isn't working, try these steps: * Ensure the batteries are correctly installed. * Check that the selected switch is set to “TV”. * Make sure you are no further than the specified distance from the TV when using the remote control.
C
chad65Aug 21, 2025
How to set adjustments to factory setting on Mitsubishi WS - 48313 Projection TV?
- D
  Deborah TerrellAug 21, 2025
  To reset your Mitsubishi Projection TV's system defaults to the factory settings: 1. Press the MENU button, followed by number buttons ?, ?, and ? on the remote control. 2. Press the ENTER button on the remote control. 3. Press the HOME or MENU button on the remote control to return to the HOME or MENU screen. IMPORTANT: This function is not recommended unless it is mandatory to reset system defaults to factory settings. This operation CANNOT be undone, and all custom settings will be erased.
C
Curtis WilsonAug 23, 2025
Why is there no sound on my Mitsubishi WS - 48313 Projection TV even when the volume is turned up?
- D
  Dylan RogersAug 23, 2025
  If you're not getting any sound from your Mitsubishi Projection TV even with the volume up, there are a few things to check: * First, make sure the MUTE button isn't activated. * Second, verify that the TV’s “Listen to:” setting isn't set to SAP. * Finally, ensure that the “TV Speakers” setting is turned On.
R
Rebecca JohnsonAug 26, 2025
Why does the sound not match the screen picture on my Mitsubishi WS - 48313?
- J
  jensencatherineAug 26, 2025
  If the sound doesn't match the picture on your Mitsubishi Projection TV, it could be due to a few reasons: * The TV’s “Listen to:” setting may be set to SAP. * If you're using stereo or A/V receiver speakers, check the input selection on the receiver. * Also, when using a stereo or A/V receiver, ensure the audio is connected from the MONITOR OUT on the TV’s back panel.
R
Rebecca ChanAug 28, 2025
What to do if I cannot access a channel on my Mitsubishi Projection TV?
- G
  garzachadAug 28, 2025
  If you're having trouble accessing a channel on your Mitsubishi Projection TV, here are some things to try: * Use the number keys instead of the CHANNEL up/down buttons. * Make sure the channel you're trying to view is stored in the TV's memory. * Verify that the TV is set to the correct input source for that channel by pressing the INPUT button. * Also, ensure that the V-Chip setting is turned Off.
J
Justin HarrisAug 30, 2025
What to do if I cannot see a picture when I play a VCR tape on my Mitsubishi Projection TV?
- A
  alexandra38Aug 30, 2025
  If you can't see a picture when playing a VCR tape on your Mitsubishi Projection TV: * If you've connected your VCR with A/V cables, use the INPUT button to select the correct input source (INPUT-?, INPUT-?, or INPUT-?) that the VCR is connected to. * Check your VCR's owner’s guide for further troubleshooting steps.
A
adamsteresaSep 1, 2025
Why does my Mitsubishi WS - 48313 take several seconds to respond to channel commands?
- R
  Rhonda SinghSep 2, 2025
  If your Mitsubishi Projection TV is slow to respond to channel commands: * Press ENTER after entering a channel number to avoid delays. * Use the three-digit number for the channel, for example, ??? for channel ?.
B
Brandon Charles PhDSep 4, 2025
How to fix picture out of focus, or colors not aligned on Mitsubishi WS - 48313 Projection TV?
- J
  jerry46Sep 4, 2025
  If the picture on your Mitsubishi Projection TV is out of focus or the colors aren't aligned, try these solutions: * Adjust the Convergence. * Check the Sharpness settings.
S
Susan WilliamsSep 6, 2025
What to do if my connected devices do not work correctly when the Mitsubishi WS - 48313 Projection TV is off?
- M
  Michele FreemanSep 6, 2025
  If connected devices aren't working correctly when your Mitsubishi Projection TV is off, it might be because the Energy Mode is set to Low. Try changing it to Standard.
N
Nathan WhiteSep 8, 2025
Why is there a large black or gray rectangle on the screen of my Mitsubishi WS - 48313 Projection TV?
- M
  Maureen FosterSep 8, 2025
  A large black or gray rectangle on your Mitsubishi Projection TV screen indicates that the TV's closed captioning is set to “text” mode, but no text information is being broadcast. Turn it Off in the CAPTIONS menu.