0180381B45 110VAC MBT250 Surface-mount/ Temperature-controlled, self-contained soldering/desoldering
or thru-hole repair station repair station for installation and removal of surface-mounted
0180300E06 220VAC devices.
8180369E97 Flux holder/applicator Allows for the proper amount of flux to be applied to pad grid
arrays for repair.
1105139W02 30cc plastic syringe For use with flux holder/applicator 8180369E97.
and flux paste
0180386A81 Miniature digital readout
soldering station
(incl. 1/64" micropoint tip)
0180386A78 Illuminated magnifying glass
with lens attachment
0180386A82 Anti-static Used during all radio assembly and
grounding kit disassembly procedures.
6684253C72 Straight prober
6680384A98 Brush
1010041A86 Solder (RMA type),
63/37, 0.020" diameter-
1 lb. spool
R-1319A Surface-Mounted Device Removal of surface-mounted integrated circuits.
(Supersedes R-1070A) Rework Station
6680332E82 R-1319A Reflow Nozzle For IC removal (approximate size 0.8 in. x 0.8 in.)
6680332E83 R-1319A Reflow Nozzle For IC removal (approximate size 0.6 in. x 0.6 in.)
6680332E84 R-1319A Reflow Nozzle For IC removal (approximate size 0.5 in. x 0.5 in.)
6680333E28 R-1319A Reflow Nozzle For removal of RF PA
R-1070A Shields and surface-mounted Removal of surface-mounted integrated circuits.
(Superseded by R-1319A) component - IC removal/rework
station (order all heat focus
heads separately)
6680334B49 0.410" x 0.410" U601, U702
6680334B50 0.430" x 0.430" U4, U5, U713
6680334B51 0.492" x 0.492" U3
6680334B52 0.572" x 0.572" U701, U705
6680334B53 0.670" x 0.790" * metal shields B, C, E, and F
6680370B51 0.475" x 0.475" U204
6680370B54 0.710" x 0.710" U710
6680370B57 0.245" x 0.245" U2, U201
6680370B58 0.340" x 0.340" U101, U102
6680371B15 0.460" x 0.560" * metal shields A, D, G, H, and I
6680371B74 0.470" x 0.570" U203
6680332E45 0.591" x 0.315" U714
6680332E46 0.862 x 0.350" U715
4
The following table lists the tools recommended for
working on this family of radios; these tools are also
available from Motorola. Note that the R-1319A
solder/desolder workstation requires the use of some
reflow nozzles. The nozzles’ part numbers and general
descriptions are listed in the table with the R-1319A.
Also note that the R-1070A workstation requires the use
of a specific “heat focus head” for each of the compo-
nents on which this item is used. Each of these heat
focus heads must be ordered separately. The indi-
vidual heat focus heads (and the components on which
they are used) are listed at the end of the table.
MOTOROLA PART NO. DESCRIPTION APPLICATION
Table 40-3. Recommended Service Tools
*
Refer to the SHIELDS LOCATION DETAIL and Shields Parts List in the rear of this manual to match the shield with the proper heat focus head.
HEAT-FOCUS INSIDE DIMENSIONS MAXIMUM PRESCRIBED
HEADS OF HEADS USED ON HEAT SETTING
Temperature settings
using the R-1319A and the
R-1070A are the same.
Refer to Maintenance Sec-
tion of Manual for
prescribed heat setting.
To Next Page
Loading...
