multivac P300 - Page 73

To Next Page

To Previous Page

Maintenance

Change the air de-oiling element

11.06.2014 73

¾ Allow the vacuum pump to cool down.

¾ Unscrew the screw plug. To do so, turn the screw plug anticlock-

wise.

¾ Pull out the air de-oiling element and dispose of it properly.

Main Page

Table of Contents2
Important Information on the Manual5
Machine Documentation5
Changes Not Covered in the Manual5
Symbols Used6
Safety8
General Safety Instructions8
Target Group8
Unauthorised Modifications and Manufacture of Spare Parts10
EC Conformity11
Intended Use11
Electromagnetic Compatibility (EMC)12
Non-Ionising Radiation12
Reasonably Foreseeable Incorrect Use12
Warning against Incorrect Use12
Residual Risks13
Obligations of the Operating Company13
Creating the Operating Directive13
Monitoring Obligation13
Making the Selection of Personnel14
Training the Personnel14
Providing Personal Protective Equipment14
Avoiding Hazards14
Providing the Installation Location14
Provide Power Supply15
Observe the Requirements for the Gas Supply15
1.7.10 Avoiding Hygiene Risks16
1.7.11 Checking the Packs17
1.7.12 Pump Protection Function18
1.7.13 Testing Pressure Equipment18
Danger Zones18
Chamber Lid20
Vacuum Pump20
Electrical System20
Safety Devices20
Machine Labelling20
Description22
Construction of the Machine22
Optional Equipment22
Gas Flushing System22
Control Terminal23
Display24
Process Sequence25
Times Which Have to be Set26
Technical Specifications27
Start-Up31
Setting up the Machine and Starting It up31
Operation41
Opening and Closing the Chamber Lid41
Switching on the Machine42
Switching off the Machine42
Setting the Times43
Packing Products43
Aborting Evacuation46
Aborting Packaging Procedure46
Working with Recipes47
Load Recipe47
Save Recipe47
Perform Pump Protection Function47
Adjustment Work and Setup49
Insert and Remove the Sloping Insert49
Cleaning50
Notes on Cleaning50
Instructions for Creating Company Cleaning Guidelines50
Instructions for Maintaining the Machine's Value51
Instructions on the Handling of Cleansers52
Instructions on the Handling of Disinfectants52
Instructions on the Handling of Anti-Corrosion Agents and Lubricants53
Instructions on the Handling of Cleaning Devices53
Cleaning Recommendations53
Care Products Table56
Maintenance59
Maintenance Schedule59
Service Recommendation60
Vacuum Pump - Perform the Pump Protection Function60
Entire Machine - Visual Inspection60
Entire Machine - Alkaline Cleaning and Disinfection61
Entire Machine - Perform a Wipe Test61
Entire Machine - Acidic Cleaning and Disinfection61
Connections - Visual Inspection61
Vacuum Pump - Checking Oil Level, Topping up61
Vacuum Pump - Oil Change62
Vacuum Pump - Exchanging the Air De-Oiling Element62
7.2.10 Entire Machine - Check the Age62
Replace the Sealing Bar62
Remove the Sealing Bar62
Install the Sealing Bar63
Repair Counter-Pressure Bar63
Open and Close the Housing65
Open Housing65
Close Housing67
Change the Oil in the Vacuum Pump68
Drain Oil68
Filling the Vacuum Pump with Oil70
Change the Air De-Oiling Element72
Change Chamber Lid Gasket74
Check the Chamber for Leaks75
Troubleshooting77
Faults with Diagnostic Message77
Faults Without Diagnostic Message77
Shutdown, Transport, Storage80
Shutting down the Machine80
Transporting the Machine80
Storing the Machine81
Disposal82
Disposing of the Machine82
Dispose of Operating Materials82
10.2.1 Disposing of Oil and Grease82
10.2.2 Disposing of Packaging Materials83
10.2.3 Dispose of Chemicals83
Spare Parts85
MULTIVAC Branch Offices87

multivac P300 - Page 73

Table of Contents

Related product manuals