Nabco GT 710 - Chapter 6: Install the Bottom Half of Inswing Arm; Section 6.1: Prepare the Swing Door for a Track with Reveal

12 of 26
GT 710-8710 OPUS Low Energy Swing Doors Quick Set-Up and Parts Guide www.NabcoEntrances.com
P/N C-00178 Rev 12-20-17
CHAPTER 6: INSTALL THE BOTTOM HALF OF INSWING ARM
SECTION 61: Prepare the Swing Door for a Track With Reveal

Table 4 Small Track Mounting Locations (12-1/4 inches)
Dim A Dim B Dim C Dim A Dim B Dim C Dim A Dim B Dim C
Reveal Butt Hinge Center Pivot Reveal Butt Hinge Center Pivot Reveal Butt Hinge Center Pivot
0 7-5/8” 7-3/16” 2-3/4” 8-11/16” 9-3/8” 5-1/2”
14-1/2”
13-13/16”
1/4” 7-3/4” 7-3/8” 3” 13-1/8” 9-9/16” 5-3/4”
1/2” 7-15/16” 7-9/16” 3-1/4” 13-3/8” 13-1/16” 6”
3/4” 8-1/8” 7-3/4” 3-1/2” 13-9/16” 13-1/4” 6-1/4”
1” 8-5/16” 7-15/16” 3-3/4” 13-3/4” 13-1/2” 6-1/2” 18-1/2”
1-1/4” 8-1/2” 8-1/8” 4” 14” 13-11/16” 6-3/4” 18-9/16” 17-7/8”
1-1/2” 8-11/16” 8-5/16” 4-1/4” 14-3/16”
13-3/4”
7” 18-9/16” 17-7/8”
1-3/4” 8-7/8” 8-1/2” 4-1/2” 14-7/16” 7-1/4”
18-5/8”
17-15/16”
2” 8-1/16” 8-3/4” 4-3/4”
14-1/2”
7-1/2” Long Track only
2-1/4” 8-1/4” 8-15/16” 5”
2-1/2” 8-1/2” 9-1/8” 5-1/4” 13-13/16”
Table 5 Large Track Mounting Locations (21 inches)
Dim A Dim B Dim C Dim A Dim B Dim C
Reveal Butt Hinge Center Pivot
no Finger Guard
Reveal Butt Hinge Center Pivot
no Finger Guard
7-1/2” Short Track only 13-1/2” 10-1/2”
19-1/4”
13-9/16”
7-3/4”
14-1/4”
13-9/16”
10-3/4” 18-5/8”
8” 11”
18-11/16”
8-1/4”
13-5/8”
11-1/4”
19-5/16”
8-1/2” 11-1/2”
8-3/4” 11-3/4”
9” 12”
9-1/4” 12-1/4”
9-1/2” 12-1/2”
9-3/4” 12-3/4”
10”
13-9/16”
13”
10-1/4” 14-3/16”



