Nabco GT 710 User Manual (English)

Other manuals for Nabco GT 710

Wiring And Adjustment Manual32 pages

Installation Manual26 pages

Questions and Answers:

S
spencecarmenSep 14, 2025
What to do if Nabco Gate Opener door slams open?
- L
  lwrightSep 14, 2025
  If your Nabco Gate Opener door slams open, it might be due to the Back Check being set too high. For GT-300/400/500 models, decrease the speed by turning the BCHK Potentiometer on the Magnum 4A Control board counterclockwise. For GT-710 models, adjust the Back Check speed on the hydraulic closer clockwise to decrease the speed. Another cause could be a misplaced back check magnet on GT-710 models; reposition the magnet to its proper location. Also, the operator may not be correctly preloaded; pre-load the operator by correctly installing the arm on the operator spindle.
G
Glen DavisAug 25, 2025
What does 'Recycle Warning' mean on my Nabco Door Opening System and how to fix it?
- L
  Lisa BanksAug 25, 2025
  If your Nabco Door Opening System displays a 'Recycle Warning', check the doorway and door resistance. If both are normal, adjust the opening and closing recycle sensitivity.
C
Catherine SmithAug 25, 2025
Why is my Nabco Door Opening System showing '62 Sensor Error', '6B Sensor Error', or 'SWL Sensor Error'?
- T
  Thomas LewisAug 26, 2025
  If your Nabco Door Opening System is showing '62 Sensor Error', '6B Sensor Error', or 'SWL Sensor Error', it may indicate that the hand-shake for the safety sensor is not working properly, or the sensor could be detecting an internal error. Check the Opus for input/output settings, harnesses, and sensor status.
B
Blake ArcherAug 27, 2025
How to fix MPU Error on Nabco Door Opening System?
- T
  travisbrownAug 27, 2025
  If the MPU Error occurs repeatedly on your Nabco Door Opening System, replace the Opus Control.
A
Amanda ButlerAug 27, 2025
What to do if my Nabco GT 710 Gate Opener does not function?
- A
  amanda79Aug 27, 2025
  If your Nabco Gate Opener isn't working, start by checking Fuse 2 (F2) and replace it if necessary. Also, verify that there is 120 VAC at Connector J5. If the power supply is good, check the connection to the motor and replace the motor if needed. Check the power to the activation device at Connector J2; if the current exceeds 0.5 amps at 24 VAC, replace it with a lower draw sensor. Finally, check Fuse 1 (F1); if it's blown, replace it. If F1 is okay, check the power to the activating devices at J2, and if the voltage is too low, reduce the accessory load.
T
Thomas JohnsonSep 12, 2025
What to do if Nabco GT 710 Gate Opener safety sensor does not function?
- S
  smithwendySep 12, 2025
  If the safety sensor on your Nabco Gate Opener isn't working, there could be a few reasons. First, check the wiring on the harness and the power to the sensor to ensure it's receiving power. Next, ensure the sensor is properly connected to the Terminal Block, connecting the output of the sensor to the correct terminals (Terminals 5 (Red) and Terminal 4 (White) for header-mounted sensors, or Terminals 5 (Red) and Terminal 3 (Violet) for door-mounted sensors). Finally, verify that Dip Switch (2) Safety is set correctly: turn Dip Switch ON for sensors using N.O. Contacts, and turn Dip Switch OFF for sensors using N.C. Contacts.
J
Jamie BrownSep 9, 2025
What to do if one sensor does not activate both doors on a simultaneous pair Nabco GT 710 Gate Opener?
- J
  jeremysmithSep 9, 2025
  If one sensor does not activate both doors on a simultaneous pair for your Nabco Gate Opener, the sensor may not be connected to both control boards. Install a Simultaneous Pair Harness (P/N 2210270).
M
manuel72Sep 10, 2025
Why does my Nabco GT 710 Gate Opener unit leak oil?
- N
  nhoSep 10, 2025
  If your Nabco Gate Opener unit is leaking oil, it's possible that the adjusting screws on the Hydraulic Closer have been removed. Replace the Hydraulic Closer.
C
Carla FletcherSep 3, 2025
What to do if the Safety or Presence Sensor does not function on Nabco GT 710 Gate Opener?
- H
  hwillisSep 3, 2025
  If the Safety or Presence Sensor on your Nabco Gate Opener isn't working, it could be due to no power to the sensor or a defective sensor. Check the harness wiring to the wire diagram.
J
Julie HolderSep 1, 2025
How to correct the direction of a Nabco GT 710 Gate Opener door?
- J
  Jesse FisherSep 1, 2025
  If your Nabco Gate Opener door moves in the wrong direction, check the polarity of the motor input wires at the connector on the motor and reverse the motor leads.