Nabco GT 710 - User Manual

Other manuals for Nabco GT 710

Wiring And Adjustment Manual32 pages

Installation Manual26 pages

Questions and Answers

T
Thomas JohnsonSep 12, 2025
What to do if Nabco GT 710 Gate Opener safety sensor does not function?
- S
  smithwendySep 12, 2025
  If the safety sensor on your Nabco Gate Opener isn't working, there could be a few reasons. First, check the wiring on the harness and the power to the sensor to ensure it's receiving power. Next, ensure the sensor is properly connected to the Terminal Block, connecting the output of the sensor to the correct terminals (Terminals 5 (Red) and Terminal 4 (White) for header-mounted sensors, or Terminals 5 (Red) and Terminal 3 (Violet) for door-mounted sensors). Finally, verify that Dip Switch (2) Safety is set correctly: turn Dip Switch ON for sensors using N.O. Contacts, and turn Dip Switch OFF for sensors using N.C. Contacts.
M
manuel72Sep 10, 2025
Why does my Nabco GT 710 Gate Opener unit leak oil?
- N
  nhoSep 10, 2025
  If your Nabco Gate Opener unit is leaking oil, it's possible that the adjusting screws on the Hydraulic Closer have been removed. Replace the Hydraulic Closer.
J
Jamie BrownSep 9, 2025
What to do if one sensor does not activate both doors on a simultaneous pair Nabco GT 710 Gate Opener?
- J
  jeremysmithSep 9, 2025
  If one sensor does not activate both doors on a simultaneous pair for your Nabco Gate Opener, the sensor may not be connected to both control boards. Install a Simultaneous Pair Harness (P/N 2210270).
N
Nicole GarciaSep 8, 2025
Why floor mat, holding beams or other accessories do not function while Nabco Gate Opener door is moving?
- D
  Diana GraySep 8, 2025
  If the floor mat, holding beams, or other accessories do not function while the Nabco Gate Opener door is moving, it may be because the accessories are connected to 'Safety w/Lockout' instead of 'Safety'. Rewire the accessory to 'Safety'.
C
Corey MartinezSep 7, 2025
Why is the Safety or Presence Sensor activated by closing door on Nabco GT 710?
- S
  Susan WoodsSep 7, 2025
  If the Safety or Presence Sensor is activated when closing the door on your Nabco Gate Opener, the sensor wiring harness may have been connected to 'Safety' instead of 'Safety w/Lockout'. Rewire the Safety Sensor to 'Safety w/Lockout'.
T
Timothy StewartAug 23, 2025
What to do if Nabco Door Opening System shows 'Drive Circuit Error'?
- K
  Kim MooreAug 23, 2025
  If your Nabco Door Opening System displays a 'Drive Circuit Error', the issue could stem from several causes: * Over current at motor. * Abnormal voltage at Motor Circuit. * Abnormal value from Motor Current detection. Check the motor connection, ensuring the Opus Control is properly connected and the motor wire isn't shorted. If the motor connection is normal, electrical noise could be the cause. It's also possible for this error to occur occasionally without indicating a problem with the door.
D
Donna RobinsonSep 5, 2025
Why does adjustment of Hydraulic Closer has no effect on Nabco GT 710 Gate Opener?
- J
  justin01Sep 5, 2025
  If adjusting the Hydraulic Closer has no effect on your Nabco Gate Opener, check the 4 pin Motor Connector on the board. Pin #2 and #4 must be jumped by a wire.
A
Amy BarnettSep 4, 2025
What to do if sensor shows activation signal sent, but Nabco GT 710 Gate Opener door does not open?
- K
  kevinreedSep 4, 2025
  If the sensor indicates an activation signal is sent but the Nabco Gate Opener door doesn't open, the sensor may not be connected properly to the activation connector. Check the harness wiring against the wiring diagram.
C
Carla FletcherSep 3, 2025
What to do if the Safety or Presence Sensor does not function on Nabco GT 710 Gate Opener?
- H
  hwillisSep 3, 2025
  If the Safety or Presence Sensor on your Nabco Gate Opener isn't working, it could be due to no power to the sensor or a defective sensor. Check the harness wiring to the wire diagram.
E
Edward SanchezSep 2, 2025
Why does my Nabco GT 710 have no back check or why does the motor continue to drive after the door is closed?
- P
  Paul BakerSep 2, 2025
  If your Nabco Gate Opener has no back check or the motor continues to drive after the door is closed, the magnets on the main sprocket may not be in the correct position. Properly align the magnets to resolve this issue.