How to fix a sticking incline assembly on my Nautilus Elliptical Trainer?
To resolve incline assembly issues on your Nautilus Elliptical Trainer, adjust the levelers to raise the front of the rail assembly until there is 0.6cm - 1.25cm (1/4” - 1/2”) space between the top of the incline assembly and the main unit shroud.
Why does my Nautilus E614 Elliptical Trainer console shut off during use?
If your Nautilus Elliptical Trainer console shuts off while you're using it, ensure the unit is plugged into a working wall outlet. Also, check the connection to make sure it's secure and undamaged; replace the adapter or connection at the unit if necessary. Finally, all wires in the cable should be intact; if any are cut or crimped, replace the cable.
What to do if my Nautilus E614 Elliptical Trainer displays 'Please Stride'?
If your Nautilus Elliptical Trainer displays 'Please Stride' or shows no speed/RPM reading, first, check that all wires in the cable are intact; replace the cable if any are cut or crimped. Next, ensure the cable is securely connected and properly oriented, making sure the small latch on the connector lines up and snaps into place. Also, confirm the magnet is in place on the pulley. Finally, the speed sensor should be aligned with the magnet and connected to the data cable; realign the sensor if needed, and replace it if damaged.
How to fix a squeaking noise on my Nautilus E614?
If you're experiencing a squeaking noise that gets worse during your Nautilus Elliptical Trainer workout, slightly loosen the pivot rod bolt until the noise stops. You can also apply white lithium grease for a temporary fix. Additionally, apply silicone lubricant to a dry cloth and wipe the rails to eliminate roller noise.
Why won't my Nautilus E614 turn on?
If your Nautilus Elliptical Trainer has no display, a partial display, or won't turn on, ensure it's plugged into a functioning wall outlet. The connection should be secure and undamaged; replace the adapter or connection if damaged. All wires in the cable should be intact; replace the cable if any are crimped or cut. Be sure the cable is connected securely and oriented properly, with the small latch on the connector lined up and snapped into place. Check for any cracks or damage to the console display and replace it if damaged. If the console only has a partial display and all connections are fine, replace the console.
How to level my Nautilus E614?
If your Nautilus Elliptical Trainer rocks or doesn't sit level, adjust the levelers until the machine is level. If the surface is extremely uneven, you may need to move the machine to a more level area.
What to do if the fan on my Nautilus E614 won't turn on/off?
If the fan on your Nautilus Elliptical Trainer won't turn on or off, make sure all wires in the cable are intact; replace the cable if any are cut or crimped. Ensure the cable is securely connected and oriented properly, with the small latch on the connector lined up and snapped into place. Unplug the unit from the electrical outlet for 3 minutes, then reconnect it.
Why is the heart rate not displaying on my Nautilus E614 Elliptical Trainer?
If your Nautilus Elliptical Trainer is operating but the contact heart rate (HR) is not displayed, make sure the cable is securely connected to the console. Also, ensure the cables from the handlebars and the cable to the console are secure and undamaged. Be sure your hands are centered on the HR sensors, kept still, and with relatively equal pressure applied to each side. A conductive electrode cream (heart rate cream) can help improve contact. If these steps don't work, the static handlebar should be replaced.
What to do if the fan on my Nautilus E614 Elliptical Trainer is not working?
If the fan on your Nautilus Elliptical Trainer won't turn on, but the console operates, unplug the unit from the electrical outlet for 5 minutes. Remove any material from the fan. If necessary, detach the console to help with removal. If you are unable to remove the blockage, replace the console.
How to tighten loose foot pedals on my Nautilus E614?
If the foot pedals on your Nautilus Elliptical Trainer feel loose or the unit is difficult to operate, tightly secure all hardware on the Pedal Arms and Handlebar Arms.
General| Type | Elliptical Trainer |
|---|---|
| Resistance Levels | 20 |
| Stride Length | 20 inches |
| Weight Capacity | 300 lbs |
| Display | LCD |
| Power Source | AC adapter |
| Display Type | LCD |
| Heart Rate Monitoring | Contact and telemetry enabled |
| Warranty | 10 year frame, 3 year parts, 1 year labor |
To Next Page
