Nautilus E618 - User Manual

Other manuals for Nautilus E618

Service Manual137 pages

Questions and Answers

J
Jaime RamosSep 12, 2025
How to fix Nautilus Exercise Bike fan that won't turn on or off?
- J
  James ValdezSep 12, 2025
  If the fan on your Nautilus Exercise Bike won't turn on or off, check that all wires in the cable are intact; replace the cable if any are cut or crimped. Ensure the cable is securely connected and properly oriented, making sure the small latch on the connector lines up and snaps into place. Try unplugging the unit from the electrical outlet for 3 minutes, then reconnect it.
J
Jacqueline WattsAug 25, 2025
Why won't my Nautilus Elliptical Trainer sync with Bluetooth?
- C
  Corey GonzalesAug 25, 2025
  If your Nautilus Elliptical Trainer isn't syncing workout results, ensure the machine is in Idle Mode by pressing the PAUSE/END button until the Power-Up Mode screen appears. Note that workouts shorter than 1 minute won't be saved. Try unplugging the unit for 5 minutes and then reconnecting it. Verify that Bluetooth® is enabled on your device and that your device is compatible with the fitness app's specifications.
K
Kimberly JonesAug 25, 2025
Why doesn't the resistance change on my Nautilus E618 Elliptical Trainer?
- C
  colleenriceAug 26, 2025
  If the resistance on your Nautilus Elliptical Trainer isn't changing, start by checking the console for any visible damage and replace it if necessary. Inspect the cable for any crimped or cut wires, and replace the cable if needed. Ensure the cable is securely connected and properly oriented, reseating all connections and making sure the small latch on the connector lines up and snaps into place. Verify that the cable from the left Upper Handlebar and the cables to the Console are secure and undamaged. If the magnets move, adjust them until they are within the proper range. If the Servo Motor is not functioning properly, replace it. If the issue persists, replace the MCB.
M
macdonaldronaldSep 23, 2025
Why does my Nautilus Elliptical Trainer console cycle through screens?
- H
  Holly OlsonSep 23, 2025
  If your Nautilus Elliptical Trainer console continuously cycles through program screens, hold down the PAUSE/END button and the Left button together for 3 seconds.
K
kimberlyleeSep 12, 2025
Why is the telemetric heart rate displayed incorrectly on my Nautilus Exercise Bike?
- F
  Frances PotterSep 12, 2025
  If your Nautilus Exercise Bike operates, but the telemetric HR is displayed incorrectly, ensure that the HR receiver is not blocked by a personal electronic device in the left side of the media tray.
T
Thomas CantrellSep 18, 2025
Why is telemetric HR not displayed on my Nautilus Elliptical Trainer?
- A
  Amanda NelsonSep 18, 2025
  If your Nautilus Elliptical Trainer isn't displaying telemetric heart rate, ensure the strap is 'POLAR®' compatible and uncoded, placed directly against the skin, and the contact area is wet. If the strap has replaceable batteries, install new ones. Select the Edit User Profile option for your profile and ensure the WIRELESS HR setting is turned ON. Try moving the unit away from potential sources of interference like TVs or microwaves. If the issue persists, replace the strap or the console.
D
Donald OlsonSep 5, 2025
Why does my Nautilus Exercise Bike console shut off while I'm using it?
- C
  Cynthia FreemanSep 5, 2025
  If the console shuts off during use, first, ensure the unit is properly plugged into a functioning wall outlet and that the connection is secure and undamaged; replace the adapter or connection if necessary. Check that all wires in the cable are intact, replacing the cable if any are cut or crimped. Also, make sure the cable is securely connected and correctly oriented, ensuring the small latch on the connector lines up and snaps into place. Try unplugging the unit from the electrical outlet for 3 minutes, then reconnect it. Finally, check that the magnet is in place on the pulley and that the speed sensor is aligned with the magnet and connected to the data cable; realign the sensor if needed, or replace it if damaged.
N
Nicholas PinedaSep 6, 2025
What to do if my Nautilus Exercise Bike shows 'Please Stride' or no speed/RPM?
- H
  Heather DunnSep 6, 2025
  If your Nautilus Exercise Bike's console displays a “Please Stride” error or there's no speed/RPM reading, start by checking the cable for any cuts or crimps and replace it if damaged. Ensure the cable is securely connected and properly oriented, making sure the small latch on the connector lines up and snaps into place. Also, verify that the magnet is in place on the pulley and that the speed sensor is aligned with the magnet and connected to the data cable. If necessary, realign the sensor or replace it if there's any damage to it or the connecting wire.
F
frankramirezSep 18, 2025
Why won't the incline adjust on my Nautilus Elliptical Trainer?
- M
  Michael McmahonSep 18, 2025
  If the incline on your Nautilus Elliptical Trainer isn't adjusting, check the console for visual damage and replace if necessary. Ensure the cable from the right Upper Handlebar and cables to the Console are secure and undamaged. Inspect all wires in the cables for cuts or crimps, and replace the cable if needed. Also, verify that the Incline Adjuster Assembly is attached to the Incline Motor drive screw.
H
harringtonerikAug 30, 2025
Why won't the fan turn on or off on my Nautilus Elliptical Trainer?
- S
  Stacey WiseAug 30, 2025
  If the fan on your Nautilus Elliptical Trainer won't turn on or off, check that all wires in the cable are intact and replace the cable if any are cut or crimped. Ensure the cable is securely connected and oriented properly, making sure the small latch on the connector lines up and snaps into place. Unplug the unit from the electrical outlet for 3 minutes, then reconnect it.