Nautilus E618 - User Manual

Other manuals for Nautilus E618

Service Manual137 pages

Questions and Answers

B
Bianca WiseAug 23, 2025
How to sync Nautilus E618 workout results with Bluetooth?
- M
  martingaryAug 25, 2025
  To sync workout results from your Nautilus Elliptical Trainer with a Bluetooth® enabled device, the machine must be in Idle Mode, so push the PAUSE/END button until the Power-Up Mode screen is displayed. Note that a workout must be longer than 1 minute to be saved and posted by the Console. Try unplugging the unit from the electrical outlet for 5 minutes, then reconnect it. Ensure that the Bluetooth® wireless feature is enabled on your device and that your device is compatible with the Fitness App.
M
moorecynthiaAug 31, 2025
What to do if my Nautilus Elliptical Trainer console cycles through screens?
- T
  tannerjasmineSep 1, 2025
  To stop the console from continuously cycling through program screens on your Nautilus Elliptical Trainer, hold down the PAUSE/END and Left button together for 3 seconds.
A
anahaynesSep 1, 2025
How to level a Nautilus Elliptical Trainer that rocks?
- J
  joseph62Sep 1, 2025
  If your Nautilus Elliptical Trainer rocks or doesn't sit level, adjust the levelers until the machine is level. If the surface is extremely uneven, adjustment may not be enough; move the machine to a more level area.
J
juliastrongSep 2, 2025
What to do if the fan won't turn on my Nautilus E618 Elliptical Trainer?
- S
  Stacy JosephSep 2, 2025
  If the fan on your Nautilus Elliptical Trainer won't turn on but the console operates, unplug the unit from the electrical outlet for 5 minutes. Remove any material from the fan. If necessary, detach the Console to help with removal. If you are unable to remove the blockage, replace the Console.
C
Carlos BradshawSep 3, 2025
How to post Nautilus Elliptical Trainer workout results to MyFitnessPal?
- T
  Traci MirandaSep 3, 2025
  To sync workout results from the Nautilus Trainer™ to MyFitnessPal® or Under Armour® Connected Fitness, select the Sync option from the Menu icon on the Nautilus Trainer™ App. Also, review your account and password for MyFitnessPal® / Under Armour® Connected Fitness.
G
Greg PhillipsSep 3, 2025
Why are the foot pedals loose on my Nautilus Elliptical Trainer?
- M
  Michael HarrisSep 4, 2025
  If the foot pedals on your Nautilus Elliptical Trainer are loose or the unit is difficult to operate, tightly secure all hardware on the Pedal Arms and Handlebar Arms.
J
Jesse PerezSep 4, 2025
How to fix knocking sound during Nautilus Elliptical Trainer operation?
- L
  Larry HardySep 4, 2025
  If you hear a knocking sound during operation of your Nautilus Elliptical Trainer, ensure that the alignment tab on the Pivot Sleeve goes into the slot in the hole and that the Pivot Sleeve extends through the opposite hole in the joint cover.
D
Donald OlsonSep 5, 2025
Why does my Nautilus Exercise Bike console shut off while I'm using it?
- C
  Cynthia FreemanSep 5, 2025
  If the console shuts off during use, first, ensure the unit is properly plugged into a functioning wall outlet and that the connection is secure and undamaged; replace the adapter or connection if necessary. Check that all wires in the cable are intact, replacing the cable if any are cut or crimped. Also, make sure the cable is securely connected and correctly oriented, ensuring the small latch on the connector lines up and snaps into place. Try unplugging the unit from the electrical outlet for 3 minutes, then reconnect it. Finally, check that the magnet is in place on the pulley and that the speed sensor is aligned with the magnet and connected to the data cable; realign the sensor if needed, or replace it if damaged.
N
Nicholas PinedaSep 6, 2025
What to do if my Nautilus Exercise Bike shows 'Please Stride' or no speed/RPM?
- H
  Heather DunnSep 6, 2025
  If your Nautilus Exercise Bike's console displays a “Please Stride” error or there's no speed/RPM reading, start by checking the cable for any cuts or crimps and replace it if damaged. Ensure the cable is securely connected and properly oriented, making sure the small latch on the connector lines up and snaps into place. Also, verify that the magnet is in place on the pulley and that the speed sensor is aligned with the magnet and connected to the data cable. If necessary, realign the sensor or replace it if there's any damage to it or the connecting wire.
M
Michael RiosSep 7, 2025
How to fix a Nautilus Exercise Bike with no display?
- M
  Meredith SmithSep 7, 2025
  If the display on your Nautilus Exercise Bike isn't working, is only partially visible, or the unit won't turn on, first ensure the unit is plugged into a functioning wall outlet. Make sure the connection is secure and undamaged, replacing the adapter or connection if necessary. Check that all wires in the cable are intact, and replace the cable if any are visibly crimped or cut. Ensure the cable is connected securely and oriented properly, with the small latch on the connector lined up and snapped into place. Check the console display for cracks or damage, and replace the console if damaged. If the console has a partial display and all connections are fine, replace the console.