What to do if my Nautilus Elliptical Trainer console cycles through screens?
To stop the console from continuously cycling through program screens on your Nautilus Elliptical Trainer, hold down the PAUSE/END and Left button together for 3 seconds.
How to fix Nautilus Exercise Bike fan that won't turn on or off?
If the fan on your Nautilus Exercise Bike won't turn on or off, check that all wires in the cable are intact; replace the cable if any are cut or crimped. Ensure the cable is securely connected and properly oriented, making sure the small latch on the connector lines up and snaps into place. Try unplugging the unit from the electrical outlet for 3 minutes, then reconnect it.
Why won't the fan turn on or off on my Nautilus Elliptical Trainer?
If the fan on your Nautilus Elliptical Trainer won't turn on or off, check that all wires in the cable are intact and replace the cable if any are cut or crimped. Ensure the cable is securely connected and oriented properly, making sure the small latch on the connector lines up and snaps into place. Unplug the unit from the electrical outlet for 3 minutes, then reconnect it.
Why are the foot pedals loose on my Nautilus Exercise Bike?
If the foot pedals on your Nautilus Exercise Bike are loose or the unit is difficult to operate, tightly secure all hardware on the Pedal Arms and Handlebar Arms.
What to do if Nautilus Exercise Bike fan won't turn on but console works?
To troubleshoot a Nautilus Exercise Bike fan that won't turn on while the console operates, unplug the unit from the electrical outlet for 5 minutes. Remove any material from the fan. If necessary, detach the console to help with removal. If you're unable to remove the blockage, replace the console.
Why is telemetric HR not displayed on my Nautilus Elliptical Trainer?
If your Nautilus Elliptical Trainer isn't displaying telemetric heart rate, ensure the strap is 'POLAR®' compatible and uncoded, placed directly against the skin, and the contact area is wet. If the strap has replaceable batteries, install new ones. Select the Edit User Profile option for your profile and ensure the WIRELESS HR setting is turned ON. Try moving the unit away from potential sources of interference like TVs or microwaves. If the issue persists, replace the strap or the console.
Why does my Nautilus Elliptical Trainer console cycle through screens?
If your Nautilus Elliptical Trainer console continuously cycles through program screens, hold down the PAUSE/END button and the Left button together for 3 seconds.
Why is the Contact HR not displayed on my Nautilus E618?
If your Nautilus Elliptical Trainer operates but the Contact HR is not displayed, ensure the cable is securely connected to the Console. Also, check that the cables from the handlebars and the cable to the Console are secure and undamaged. Make sure your hands are centered on the HR sensors and kept still with relatively equal pressure applied to each side. A conductive electrode cream can help improve contact. If these steps don't work, the Static Handlebar should be replaced.
What to do if my Nautilus E618 Elliptical Trainer console shuts off during use?
If the console of your Nautilus Elliptical Trainer shuts off or enters sleep mode during use, ensure the unit is plugged into a functioning wall outlet and that the connection is secure and undamaged; replace the adapter or connection if necessary. Check the cable for any cut or crimped wires, replacing it if needed, and ensure the cable is securely connected and properly oriented, with the small latch on the connector lined up and snapped into place. Unplug the unit from the electrical outlet for 3 minutes, then reconnect it. Verify that the magnet is in place on the pulley. Also, check that the speed sensor is aligned with the magnet and connected to the data cable; realign the sensor if necessary, and replace it if damaged.
Why doesn't the resistance change on my Nautilus E618 Elliptical Trainer?
If the resistance on your Nautilus Elliptical Trainer isn't changing, start by checking the console for any visible damage and replace it if necessary. Inspect the cable for any crimped or cut wires, and replace the cable if needed. Ensure the cable is securely connected and properly oriented, reseating all connections and making sure the small latch on the connector lines up and snaps into place. Verify that the cable from the left Upper Handlebar and the cables to the Console are secure and undamaged. If the magnets move, adjust them until they are within the proper range. If the Servo Motor is not functioning properly, replace it. If the issue persists, replace the MCB.
Essential safety guidelines for operating and assembling the fitness equipment.
Attaching the front stabilizer, rail assembly, and legs to the main frame.
Connecting the console mast, handlebars, and console.
Instructions for connecting the leg components and pedals to the frame.
Installing the arm pivot rod and handlebar arms onto the machine.
Attaching the upper handlebar arms and handlebar shrouds.
Connecting the power cord and performing a final inspection before use.
Advice on workout frequency, duration, and proper mounting/dismounting.
Details on Power-Up/Idle Mode, initial setup, and starting Quick Start workouts.
Solutions for problems like no display, partial display, or incorrect HR readings.
Fixes for contact or telemetric heart rate not displaying or displaying incorrectly.
Troubleshooting steps for resistance not changing or incline not adjusting.
General| Display | LCD |
|---|---|
| Programs | 29 |
| Heart Rate Monitoring | Contact and telemetry enabled |
| Bluetooth Connectivity | Yes |
| User Profiles | 4 |
| Maximum User Weight | 300 lbs |
To Next Page
