EasyManuals Logo

NETGEAR GS748T - ProSafe Smart Switch User Manual

NETGEAR GS748T - ProSafe Smart Switch
36 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #3 background imageLoading...
Page #3 background image
v1.1, September 2007
iii
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
EN 55 022 Declaration of Conformance
This is to certify that the NETGEAR GS748T Gigabit Smart Switch is shielded against the generation of radio
interference in accordance with the application of Council Directive 89/336/EEC, Article 4a. Conformity is de-
clared by the application of EN 55024 Class A (CISPR 22).
EN 55 022 and EN 55 024 Statements
This is to certify that the NETGEAR GS748T Gigabit Smart Switch is shielded against the generation of radio interference
in accordance with the application of Council Directive 89/336/EEC, Article 4a. Conformity is declared by the application of
EN 55 022 Class A (CISPR 22) and EN 55 024.
Canadian Department of Communications Radio Interference Regulations
This digital apparatus (NETGEAR GS748T Gigabit Smart Switch) does not exceed the Class A limits for radio-noise
emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of
Communications.
Règlement sur le brouillage radioélectrique du ministère des Communications
Cet appareil numérique (NETGEAR GS748T Gigabit Smart Switch) respecte les limites de bruits radioélectriques visant
les appareils numériques de classe A prescrites dans le Règlement sur le brouillage radioélectrique du ministère des
Communications du Canada.
Customer Support
For assistance with installing and configuring your NETGEAR system or for questions or problems following
installation:
Check the NETGEAR Web page at http://www.NETGEAR.com/support
Call Technical Support in North America at 1-888-NETGEAR. If you are outside North America, please
refer to the phone numbers listed on the Support Information Card that was included with your switch.
Email Technical Support at support@NETGEAR.com.
Defective or damaged merchandise can be returned to your point-of-purchase representative.
Internet/World Wide Web
NETGEAR maintains a World Wide Web home page that you can access at the uniform resource locator (URL) http://
www.NETGEAR.com. A direct connection to the Internet and a Web browser such as Internet Explorer or Netscape are
required.
Note: Warning: This is a Class A product. In a domestic environment, this product may
cause radio interference, in which case the user may be required to take
appropriate measures.

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the NETGEAR GS748T - ProSafe Smart Switch and is the answer not in the manual?

NETGEAR GS748T - ProSafe Smart Switch Specifications

General IconGeneral
ModelGS748T
Device TypeSmart Switch
SFP Slots4
Form FactorRack-mountable
Switching Capacity96 Gbps
MAC Address Table Size8K entries
VLAN SupportYes
QoSYes
Humidity10% to 90% non-condensing
RAM128 MB
Flash Memory32 MB
Power DeviceInternal power supply
Ports48 x 10/100/1000
ManagementWeb-based
Operating Temperature0 - 50 °C
Voltage Required100-240 VAC
Compliant StandardsIEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3z
FeaturesVLAN support, QoS, port mirroring, SNMP

Related product manuals