CAUTIONS AND NOTES 4
EXTREMELY IMPORTANT 4
ETL DEFINITIONS COMPLIANT TO UL325 4
1 - OVERVIEW 4
1.1 - Main control board 4
1.2 - Main control board specics 4
2 - GATE INFORMATION 4
2.1 - ASTM F2200 4
2.2 - Gate latches 5
2.3 - Specic applications 5
2.4 - Swing gates 5
2.5 - General requirements 5
3 - SAFETY AND CAUTIONS 5
3.1 - Properly installed safety devices 5
3.2 - Safety signs, notices to personnel warning signs 5
3.3 - Gate system safety devices 6
3.4 - Infrared beams and warning signs 6
3.5 - Establish the location 6
3.6 - Read and follow all instructions 6
3.7 - Keep children away 6
3.8 - Test the gate system 6
3.9 - Keep gates properly maintained 6
4 - INSTALLATION NOTES
4.1 - Follow Instructions 6
4.2 - Intended usage 6
4.3 - Warnings, cautions and notes 6
5 - CIRCUIT BOARD LAYOUT 8
6 - INCOMING POWER WIRING 8
7 - CONTROL BOX MOUNTING 9
8 - NT-T51K & NT-T71K INSTALLATION 10
8.1 - Parts identication 11
8.2 - Pivot arm installation 11
8.3 - T5 Pivot arm bracket location graph 12
8.4 - T7 Pivot arm bracket location graph 13
8.5 - Gate bracket mounting 14
8.6 - Actuator mounting 14
8.7 - Actuator wiring 15
8.8 - Limit & motor connection to the board 15
8.9 - Limit switch adjustment 16
9 - 15501K & 16501K INSTALLATION 17
9.1 - Parts identication 17
9.2 - Pull to open installation 18
9.3 - Push to open installation 19
9.4 - Actuator mounting 19
9.5 - Actuator wiring 20
9.6 - Gate bracket mounting 20
9.7 - Limit & motor connection to the board 21
9.8 - Limit switch adjustment 21
9.9 - Setting limit switches 22
10 - 35001K & 36001K INSTALLATION 23
10.1 - Parts indentication 23
10.2 - Post installation 24
10.3 - Chassis mounting 25
10.4 - Control arm assembly 26
10.5 - Gate bracket mounting 27
10.6 - Chassis wiring 27
10.7 - Limit & motor wiring 28
10.8 - Limit & motor connection to the board 28
10.9 - Setting limit switches 29
11 - LEARNING MODE 30
12 - ACCESSORY INPUTS AND OUTPUTS 31
12.1 - Outputs 31
12.2 - Inputs 31
12.3 - Communication buses 32
12.4 - Programming the plug-in receiver and remote controls 32
13 - 120VAC POWER WIRING 33
14 - SOLAR PANEL CHART 33
15 - OPTIONAL INPUTS 34
15.1 - Fire dept. connection 34
15.2 - Magnetic lock connection 34
15.3 - Guard station 34
15.4 - Exit and edge inputs wiring diagram 34
15.5 - Radio receiver connection (third party) 35
15.6 - Optional power output 35
16 - INSPECTION AND OPERATION 35
17 - GENERAL LAYOUT AND SAFETY ACCESS 36
18 - ACCESSORIES AND SENSORS 37
19 - BOARD NOMENCLATURE 38
20 - PROGRAMMING BUTTONS 39
20.1 - Force 39
20.2 - Speed 39
20.3 - Acceleration 39
20.4 - Delay 39
20.5 - Function 39
20.6 - Display 40
21 - EMERGENCY VEHICLE ACCESS 41
22 - GLOSSARY 41
23 - MAINTENANCE SCHEDULE 42
24 - TROUBLESHOOTING 42
25 - CONTROL BOX DIMENSIONS 43
26 - EXPLODED VIEW 44
27 - WARRANTY 45
28 - INSTALLATION CHECKLIST 46
TABLE OF CONTENTS
To Next Page
Loading...
Need help?
General