Nord Drivesystems NORDAC FLEX SK 215E Series User Manual

NORDAC FLEX (SK 200E ... SK 235E) – Users Manual for Frequency Inverters
134 BU 0200 en-3118
Pos: 28 1 /Anlei tung en/El ektr onik/FU und Star ter/5 . Par ameter /Al lge mei n/Par ame ter übers ic ht_0 2_4-Steuerklemmen [SK 1x0E, SK 2xxE] @ 9\mod_1447414720702_388.docx @ 263608 @ @ 1
Control terminals
P400
Function Setpoint inputs
P401
Analogue input mode
P402
Adjustment: 0%
P403
Adjustment: 100%
P404
Analogue input filter
P410
Min. freq. Auxiliary
setpoint
P411
Max. Freq. Auxiliary
setpoint
P412
Nom. val. process ctrl.
P413
PI control P comp.
P414
PI control I comp.
P415
Limit process ctrl.
P416
Ramp time PI setpoint
P417
Offset analogue output
P418
Funct. analogue output
P419
Standard analogue
output
P420
Digital inputs
P426
Quick stop time
P427
Emerg. stop Fault
P428
Automatic starting
P434
Digital output function
P435
Dig. out scaling
P436
Dig. out. hysteresis
P460
Watchdog time
P464
Fixed frequency mode
P465
Fixed freq. Array
P466
Minimum freq. process
control
P475
delay on/off switch
P480
Function BusIO In Bits
P481
Function BusIO Out Bits
P482
Standard BusIO Out
Bits
P483
Hyst. BusIO Out Bits
Pos: 28 2 /Anlei tung en/El ektr onik/FU und Star ter/5 . Par ameter/ Allg emei n/Par ameter übers icht_ 02_5-Z usatzparameter [SK 1x0E, SK 2xxE, SK 2xxE-FDS] @ 9\ mod_1447415583483_388.docx @ 263641 @ @ 1
Extra parameters
P501
Inverter name
P502
Master function value
P503
Leading function output
P504
Pulse frequency
P505
Absolute minimum freq.
P506
Auto. Fault
acknowledgement
P509
Control word source
P510
Setpoint source
P511
USS baud rate
P512
USS address
P513
Telegram timeout
P514
CAN bus baud rate
P515
CAN bus address
P516
Skip frequency 1
P517
Skip freq. area 1
P518
Skip frequency 2
P519
Skip freq. area 2
P520
Flying start
P521
Flying start Resolution
P522
Flying start Offset
P523
Factory setting
P525
Load control max
P526
Load control min
P527
Load monitoring Freq.
P528
Load monitoring delay
P529
Mode Load control
P533
Factor I²t
P534
Torque shutoff lim.
P535
I²t motor
P536
Current limit
P537
Pulse disconnection
P539
Output monitoring
P540
Mode phase sequence
P541
Set relays
P542
Set analogue out
P543
Bus - Actual value
P546
Function Setpoint Bus
value
P549
Pot Box function
P550
EEPROM Copy Order
P552
CAN master cycle
P553
PLC setpoint
P555
P - limit chopper
P556
Braking resistor
P557
Braking resistor type
P558
Flux delay
P559
DC Run-on time
P560
Parameter, saving mode
Pos: 28 3 /Anlei tung en/El ektr onik/FU und Star ter/5 . Par ameter/ Allg emei n/Par ameter übers icht_ 02_6-P osi tioni er ung [SK 2x xE, SK 2xx E-FDS ] @ 9 \mod_1447415705800_388.docx @ 263674 @ @ 1
Positioning
P600
Position control
P601
Actual position
P602
Actual setpoint position
P603
Actual Pos. diff.
P604
Encoder type
P605
Absolute encoder
P607
Ratio
P608
Reduction ratio
P609
Offset Position
P610
Setpoint Mode
P611
Position controller P
P612
Pos. window
P613
Position
P615
Maximum Position
P616
Minimum Position
P625
Output Hysteresis
P626
Comparative position
output
P630
Position slip error
P631
Slip error. Abs./inc.
P640
Unit of pos. value
Pos: 284 /Allg em ein/ All ge meing ülti g e Mod ule /---------Seiten umbr uch ko mpakt --------- @ 13\mod_1476369695906_0.docx @ 2265495 @ @ 1

Nord Drivesystems NORDAC FLEX SK 215E Series Specifications

General

Brand	Nord Drivesystems
Model	NORDAC FLEX SK 215E Series
Category	Inverter
Language	English