How to fix water leaks between handpiece and hose in NSK Medical Equipment?
If water is leaking from between the Handpiece and Handpiece Hose of your NSK Medical Equipment, replace the O-ring in the Handpiece joint section, apply a drop of the supplied turbine oil and rub it in with your finger.
Why do alarms sound and the powder and tooth icon blink on my NSK Medical Equipment?
If you hear alarms and see "POWDER" and the tooth icon blinking alternately when you press Foot Control button D or B on your NSK Medical Equipment, try these solutions: * Wipe the sensor clean, as it may be dirty and mistakenly detecting the Handpiece. * Ensure the Chamber is securely attached until you hear the confirmation sound.
Why is there no or poor vibration in my NSK Varios Combi Pro?
There could be several reasons for the lack of vibration. Ensure the AC power cord is properly connected to a working wall socket. Check the fuse and replace it if necessary, referring to section "10-5 Replacing the fuse". Make sure the Tip is tightened firmly using the Tip Wrench until it clicks; a worn Tip may also cause this, so replace it. Clean the screw parts of the Handpiece and Tip. Adjust the power to the appropriate level for the Tip, consulting the Tip-Power Guide or the Tip case label. Finally, ensure the Foot Control is correctly connected.
What to do if my NSK Varios Combi Pro makes a beeping sound?
A beeping sound could indicate that the power was turned on while the Foot Control was depressed; release the Foot Control and turn the POWER switch to ON. Alternatively, it might be due to abnormal heating of the Control Unit; in this case, stop operation and allow the Control Unit to cool down.
Why is my NSK Varios Combi Pro handpiece overheating?
The handpiece may overheat if the power hasn't been properly adjusted for the tip. Adjust the power, ensuring it does not exceed the maximum level specified in the Tip-Power Guide or on the Tip case label. Also, ensure the Tip is firmly tightened using the Tip Wrench until it clicks, replacing the wrench if the issue continues. Insufficient irrigation volume or stopped irrigation can also cause overheating; ensure adequate irrigation volume.
Why is my NSK Medical Equipment beeping?
If your NSK Medical Equipment is beeping, it could be due to: * The power was turned on while the Foot Control was depressed. Release the Foot Control and turn the POWER switch to ON. * Abnormal heating of the Control Unit. Stop operation and allow the Control Unit to cool down.
What to do if NSK Medical Equipment is leaking water?
If you're experiencing water leakage with your NSK Medical Equipment, here are a couple of things to check: * Make sure the Irrigation Tube is fully inserted into the Irrigation Connector. * Inspect the O-Ring at the Handpiece Cord for wear or damage, and replace it if necessary.
Why is my NSK Medical Equipment handpiece making noise?
If you are experiencing noise from the handpiece of your NSK Medical Equipment, consider the following: * Adjust the power to the appropriate level as indicated in the Tip-Power Guide or on the Tip case label. * Ensure the Tip is tightened firmly using the Tip Wrench. If the problem persists, the Tip Wrench may need replacement.
What to do if water leaks from between the handpiece and handpiece hose of my NSK Varios Combi Pro Laboratory Equipment?
If water is leaking from between the Handpiece and Handpiece Hose, the O-ring may be scratched. Replace the O-ring in the Handpiece joint section, then apply a drop of the supplied turbine oil and rub it in with your finger. (Refer to "10-1-2 Handpiece Hose (for Prophy use and Perio use).")
Why does the tip fall off my NSK Laboratory Equipment?
If the Tip falls off, it is likely not tightened firmly enough. Tighten the Tip using the Tip Wrench until you hear a click.
General warnings and cautions for ultrasonic and powder modes.
Confirming no abnormal vibration, noise, heat, and checking LEDs/water flow.
Step-by-step guide to attaching the tip to the handpiece.
Procedures for setting up the water supply for powder mode.
How to prepare and load powder into the chamber.
Guidelines for using the Prophy and Perio modes.
Procedure for automatic cleaning of the ultrasonic handpiece.
Methods for cleaning the ultrasonic handpiece.
Procedure for automatic cleaning of the powder handpiece.
Steps to clean the powder handpiece interior and exterior.
How to clean the handpiece cords and plugs.
Procedure for ultrasonic cleaning of handpiece and nozzle.
Procedures and items for sterilizing the device components.
How to use the sterilization case for handpieces and tips.
Steps to clean the chamber and hoses.
How to clean the control unit and foot control.
How to replace the O-rings on the handpiece cord.
How to replace O-rings on the handpiece hose.
How to replace O-rings on the nozzle.
Table of error codes and their descriptions/remedies.
Solutions for common issues encountered during operation.
General| Brand | NSK |
|---|---|
| Model | Varios Combi Pro |
| Category | Laboratory Equipment |
| Language | English |
To Next Page
