Oki lan 8100e - User Manual

140 pages

Save Page as PDF

To Next Page

Main Page

Questions and Answers

W
Wayne KellyAug 25, 2025
What to do if Oki lan 8100e doesn't print after clearing jam?
- D
  David PhillipsAug 26, 2025
  If your Oki Printer continues not to print after clearing a jam, raise and gently lower the top cover, especially if the paper jam was removed from behind the front cover.
D
Denise GonzalezAug 26, 2025
Why does my Oki lan 8100e frequently jam?
- P
  phillip74Aug 26, 2025
  To address frequent paper jams in your Oki Printer, ensure the printer is on a stable, level surface and that you're using the correct type of paper. Store paper within specified temperature and humidity levels. Remove any creased or wrinkled paper, and adjust the tray or manual feed guides. Also, verify the correct paper feed selection in the printer driver's Properties Setup tab.
S
Sherry PetersonAug 26, 2025
What to do if Oki lan 8100e does not go online?
- J
  John LewisAug 26, 2025
  If your Oki Printer does not go online, switch it off and disconnect the power cable. Reconnect the power cable and switch the printer back on. If this does not clear the fault, call for service.
C
Colton DixonAug 27, 2025
How to replace toner on Oki lan 8100e when it's empty?
- A
  Autumn SnyderAug 27, 2025
  To resolve a 'REPLACE TONER nnn: * TONER EMPTY' error on your Oki Printer, replace the indicated toner. The codes are: 410: Y = Yellow, 411 M = Magenta, 412: C = Cyan, 413: K = Black.
H
hawkinsseanAug 27, 2025
Why does my Oki lan 8100e Printer say 'ADD MORE MEMORY 420: MEMORY OVERFLOW'?
- T
  Teresa FernandezAug 27, 2025
  If your Oki Printer displays 'ADD MORE MEMORY 420: MEMORY OVERFLOW', it means the document is too large for the printer's memory. Try reducing the document size. If this happens often, consider installing additional memory.
S
Steven BradshawAug 27, 2025
What to do if Oki lan 8100e Printer shows 'CHECK FUSER 320: FUSER MISSING' error?
- W
  wrightstephenAug 28, 2025
  If your Oki printer displays the error 'CHECK FUSER 320: FUSER MISSING', open the top cover and ensure the fuser unit is properly seated. Also, check that the lock levers are pushed all the way toward the back of the printer.
D
Deborah RodriguezAug 28, 2025
How to fix 'CHECK BELT 330: BELT MISSING' error on Oki lan 8100e Printer?
- G
  Gregory RiosAug 28, 2025
  If your Oki Printer displays 'CHECK BELT 330: BELT MISSING', open the top cover and remove the black (K) and Yellow (Y) image drums. Ensure the belt unit latches are fully latched, then reinstall the image drums.
R
Ronald MendozaAug 28, 2025
What does 'YYYY nnn: FATAL ERROR' mean on my Oki lan 8100e Printer?
- D
  David CookAug 29, 2025
  If you see 'YYYY nnn: FATAL ERROR' on your Oki Printer, try turning it off and then back on. If the problem persists, write down the message, including the error number “nnn,” and any scrolling octets, then contact your authorized Oki Data Service Dealer.
J
Jared ReedAug 29, 2025
How do I fix the 'CLOSE COVER 316: DUPLEX COVER OPEN' error on my Oki lan 8100e Printer?
- C
  Connor JohnsonAug 29, 2025
  To resolve the 'CLOSE COVER 316: DUPLEX COVER OPEN' error on your Oki Printer, ensure that the duplex cover is fully closed and properly latched.
S
srubioAug 29, 2025
Why does my Oki lan 8100e say 'INSTALL PAPER CASSETTE 430: TRAY 1 MISSING'?
- J
  James FloresAug 30, 2025
  If your Oki Printer displays 'INSTALL PAPER CASSETTE 430: TRAY 1 MISSING', it means Tray 1 is not installed. Install the missing tray to resolve the issue.