To Next Page
G
Garrett DavisSep 5, 2025
What to do if Olympus IPLEX NX IV9435N displays
- JjameslawsonSep 5, 2025
If you see this message, it means the file name you are trying to use already exists. Specify a file name that is different from the existing one.
What to do if Olympus IPLEX NX IV9435N displays
If you see this message, it means the file name you are trying to use already exists. Specify a file name that is different from the existing one.
What should I do if my Olympus IPLEX NX IV9435N displays
If your device shows this message, it means the SDHC card or USB flash drive is full. You should delete any unnecessary data to create more space, or replace it with a new SDHC card or USB flash drive.
Why is my Olympus IPLEX NX IV9435N image not sharp?
The lack of sharpness may be due to a dirty objective lens on the distal end of the insertion tube or the optical adapter. Try wiping it with a clean piece of gauze or a cotton swab. Also, ensure the optical adapter is correctly attached and that both the image sharpness and external monitor are properly adjusted.
What to do if Olympus IPLEX NX IV9435N displays
This message indicates that the battery voltage is low. Stop all operations like recording, copying, deleting, or formatting the USB flash drive. Replace the battery immediately or connect the AC adapter.
Why is my Olympus IPLEX NX IV9435N not turning on?
Several reasons may prevent the system from turning on. Make sure the AC adapter or battery is correctly connected. Ensure the power is switched ON. Verify that you are using the designated AC adapter or battery. Finally, check that the scope unit is properly attached to the main unit.
Why does my Olympus IPLEX NX IV9435N Industrial Equipment optical adapter not attach to the insertion tube?
The inability to attach the optical adapter could be due to a foreign object stuck to the screws. Try wiping with a clean piece of gauze or a cotton swab. It could also be that you are not using the designated optical adapter for this system, so ensure you are using the correct adapter. Finally, the installation procedure may be incorrect.
Why won't my Olympus IPLEX NX IV9435N Industrial Equipment turn off?
If the system cannot be turned off, the main unit might be damaged. Remove the AC adapter or the battery from the main unit and turn OFF the power.
What to do if Olympus IPLEX NX IV9435N displays
This message indicates that the self-check function was activated due to an overcurrent in the light source. Terminate the inspection, allow the instrument to cool down, and then turn the power back on again.
What to do if Olympus Industrial Equipment displays
This message indicates that the distal end has become too hot, activating the self-check function. Immediately pull the insertion tube out of the observation object.
How to fix Olympus IPLEX NX IV9435N Industrial Equipment if illumination does not light?
If the illumination does not light, ensure that the [LIGHT] button is turned ON.
General| Model | IPLEX NX IV9435N |
|---|---|
| Category | Industrial Videoscope |
| Resolution | 640 x 480 pixels |
| Light Source | LED |
| Working Length | 3.5 m |
| Field of View | 90° |
| Weight | 2.9 kg |
| Storage Temperature | -20 °C to 60 °C |
| IP Rating | IP55 |
| Image Sensor | CMOS |
| Insertion Tube Diameter | 4.0 mm |
| Direction of View | Forward |
Essential precautions for safe handling and use of the instrument.
Specific safety measures for handling and attaching the hook assembly.
Precautions for safe use, charging, and disposal of the instrument's battery.
Instructions for loading the battery and connecting the AC adapter.
Checklists for ensuring instrument integrity before and after use.
Steps to turn the instrument on and adjust illumination levels.
Guidance on using controls, observing objects, and withdrawing components.
Procedures for capturing, saving, and reviewing images and movies.
Verifying measurement accuracy before and after the procedure.
Detailed guide on performing measurements and recording results.
Detailed guide on setting reference points, length, and recording results.
Guidance on identifying and resolving instrument issues and error indicators.
Addressing frequently encountered issues and their recommended fixes.
