Selecting an Audio Component
Using the tone control:
To make bass and treble adjustment work for multichannel sources,
you must first set the tone control to "On."
To turn on the tone control:
1. Press the SURROUND button (or SURR button on the
remote controller).
TX-SR701/TOf E/601/601 E Remote controller
4
"Tone On" appears on the display and the tone control is turned
on,
2. Press the AUDIO ADJUST button and then the a and
• cursor buttons to select Bass (orTreble).
TX-SR701/701E/601/601 E Remote controller
AIJ_O _J[_O A_JU_T
ADJUST (_
4
3. Press the • and • cursor buttons to set the desired
level.
TX-SR701/701E/601/601 E Remote controller
To turn off the tone control:
Press the DIRECT button,
TX-SR701/7OIE TX-SR6OI/601E Remote
controller
DI_EC_
PUREAUDIO 2
"Direct" appears on the display and the tone control is turned
off.
Notes:
• (TX-SRT01/701E only) When you turn on the tone control, the
sellings in "Speaker Config" and "Speaker Distance" will be
used for multichannel playback.
• (TX-SRT01/701E only) When you play back multichannel
soumes, you can select the Pure Audio mode by pressing the
PURE AUDIO button.
'Ii) exit the Pure Audio mode, press the DIRECT or
SURROUND button.
• If you change the speaker levels in step 4 above, these new
levels for multichannel sources will have no effect on the
settings at "Level Calibra/ion."
I Switching the display
While listening to or watching an input source, you can display the
informa/ion regarding the type of source and signal being input by
pressing the DISPLAY button on the TX-SR701/701E/601/601E or
the remole controller.
You can set separate video displays for when the input soume is set
to AM or FM broadcasts and for when it is set to anything else.
TX-SR7Ol/701 E/601601/601 E
Remote controller
+10
When an input source other than FM or AM is selected:
Input + volume [ ..,"),.../1_7
Program format or ......
sampling [ ; _"_ ; t.. ,.. _", -: .-"- .= 7L.., .'d .L Ld .= L,," _,,: ." ,w/. n ;
frequency*
ST
Input + Listening l r'_i ii", r'_.-. 7 /- ...- .,"_.
mode or aultich t....,., t... t... a..,_. t_,., t...
* When the input signal is digital audio
The program format is displayed. For example, the display
"Dolby D: 3/2.1" shows thai the formal is Dolby Digital with
5.1 discrete channels consisting of three front channels (front
left, front right, and center), two surround channels (surround
left and surround right), and the low frequency efl_ct (LFE)
channel.
When the front channel number is 2, they are the fiont lefl and
front right; when it is I, it is monaural. When the surround
channel number is I, it is monaural; when it is 0, there is no
surround channel. When the LFE number is 0, there is no LFE
channel. Also, if there is no program format for the input signal,
nothing will be displayed.
When the input signal is linear PCM
The sampling frequency is displayed. For example, the display
"PCM fs: 44.1k" shows thai the signal is PCM and that the
sampling frequency is 44.1 kHz.
When FM or AM is selected as the input source:
FM/AM frequency+ / .......-, ,-,-,,-..... i
L
J JJ JJ J..
_. _.- a ........... J.
Preset no. ' ' ' '
$
FM/AM +
Listening
I L:'="' '=," _, _ ,-'5
mode .,.,., "-" .::'.:'= --:"-"
I
I Temporarily turning off the sound
To turn off the sound momentarily, press the
MUTING button on the remote controller. The
MUTING indicator will flash and the sound fi-om
the speakers or headphones will be switched off
by the receiver's audio muting circuit. Press the
MUTING button again to turn the sound back on.
Remote
controller
MbTINQ
Flashes
.tqu i r g
45
To Next Page
Loading...
