To Next PageTo Next PageWhy cannot copy scenes on Panasonic HDC-SD40 Camcorder SD card via USB?
If you cannot copy scenes from the SD card of your Panasonic Camcorder when connecting to other equipment via USB, the other equipment might not have recognized the SD card. Try unplugging and reconnecting the USB cable.
What to do if Panasonic HDC-SD40 is not detected by PC via USB?
If your Panasonic Camcorder is not detected by the PC when connected by the USB cable: * Re-insert the SD card into the unit, then reconnect the supplied USB cable. * Try a different USB terminal on the PC. * Ensure you are within the operating environment. * Restart the PC and the unit, then reconnect the supplied USB cable.
Why is there no video or audio output from my Panasonic HDC-SD40 Camcorder to TV?
If your Panasonic Camcorder is connected to the TV correctly but there is no video or audio output, or the images are squeezed horizontally, read the operating instructions of your TV and select the channel that matches the input used for the connection. Also, change the [TV ASPECT] setting to match the aspect ratio of the TV and change the setting of the unit depending on the cable connecting to the TV. Check the screen of the unit if the TV screen is not displayed during recording or when PRE-REC is set. Note that audio is not output from the TV during recording mode.
What to do if Panasonic HDC-SD40 is on but not working?
If your Panasonic Camcorder is on but not working correctly, try removing the battery or AC adapter, waiting about a minute, and then reconnecting it. Wait another minute before turning the unit back on. If the issue persists, disconnect the power and contact consumer support.
How to import AVCHD scenes with iMovie’11 from Panasonic HDC-SD40?
If you're unable to import AVCHD scenes with iMovie’11 from your Panasonic Camcorder, and both AVCHD and iFrame scenes are recorded on the same media, first copy all the iFrame scenes data to iMovie’11. Then, delete all the iFrame scenes data on the media before importing the AVCHD scenes with iMovie’11.
What does 'Error occurred' mean on Panasonic HDC-SD40?
If the message “ERROR OCCURRED. PLEASE TURN UNIT OFF, THEN TURN ON AGAIN.” is displayed on your Panasonic Camcorder, restart the unit by turning it off and on again. If the message repeatedly appears after restarting, repair is needed. Disconnect the power and consult the dealer from whom you purchased the unit.
How to fix incorrect battery display on Panasonic Camcorder?
If the remaining battery indication is not displayed properly on your Panasonic Camcorder, fully charge the battery, discharge it, and then charge it again.
What to do if Panasonic HDC-SD40 displays 'Error occurred'?
If your Panasonic Camcorder displays the message “ERROR OCCURRED. PLEASE TURN UNIT OFF, THEN TURN ON AGAIN,” the unit has detected an error. Try restarting the unit by turning it off and then on again. If the error message continues to appear after restarting, disconnect the power and contact consumer support, as repair may be needed.
What to do if Panasonic Camcorder SD card is not recognized in other device?
If an SD card from your Panasonic Camcorder isn't recognized in another device, verify that the device supports the SD card's capacity or type (SD Memory Card/SDHC Memory Card/ SDXC Memory Card).
Why Panasonic HDC-SD40 Camcorder turns off automatically?
If your Panasonic Camcorder turns off automatically, and the unit turns off when you turn off the power to the TV using the TV remote control, the VIERA Link is at work. If you are not using the VIERA Link, set [VIERA Link] to [OFF].
General| Digital zoom | 1200 x |
|---|---|
| Optical zoom | 16.8 x |
| Image stabilizer | Yes |
| Focal length range | 2.9 - 48.7 mm |
| Focal length (35mm film equivalent) | 42.9 - 721 mm |
| Sensor type | MOS |
| Total megapixels | 1.5 MP |
| Optical sensor size | 1/5.8 \ |
| Effective megapixels (movie) | 1.19 MP |
| Interface | USB 2.0 |
| Video out | 1 |
| Power requirements | AC/DC, 3.6 - 5.0 V |
| Power consumption (typical) | 7.7 W |
| Display diagonal | 2.7 \ |
| Maximum video resolution | 1920 x 1080 pixels |
| Image formats supported | JPG |
| Still image resolution(s) | 1920 x 1080 |
| Audio system | Dolby Digital |
| Camera shutter speed | 1/25 - 1/8000 s |
| Shutter speed (photo) | 1/25 s |
| Shutter speed (video) | 1/8000 s |
| Minimum illumination | 1 lx |
| USB 2.0 ports quantity | USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them. |
| Compatible memory cards | SD, SDHC, SDXC |
| Product color | White |
| Bundled software | HD Writer LE 1.0 |
Weight and Dimensions| Depth | 108.5 mm |
|---|---|
| Width | 51.5 mm |
| Height | 57.5 mm |
| Weight | 169 g |
Precautions for using the camera in various environments and locations.
Step-by-step instructions for inserting the camera's battery.
Procedure for charging the camera's battery using the AC adaptor.
Step-by-step guide on how to insert and remove the battery.
Adjusting white balance for accurate color reproduction in different lighting conditions.
Controlling shutter speed and iris for exposure and image brightness.
Using on-screen icons to control motion picture playback functions.
Guide on connecting the camcorder to a television for playback.
Instructions for copying recorded content from internal memory to an SD card.
Overview of PC operations using HD Writer LE 1.0 software.
General advice on handling the unit and avoiding electromagnetic interference.
Instructions in Spanish for inserting the battery into the device.
Instructions in Spanish for charging the battery using the AC adaptor.
