To Next PageTo Next Page
Why originating an outside call cannot be performed on Panasonic KX-TDA30 PBX?
If you cannot originate an outside call, transfer a call, or start a conference on your Panasonic PBX, the corresponding CO button may not be programmed on the PT. Program the CO button.
What to do if Panasonic KX-TDA30 shows improper operation?
If your Panasonic PBX exhibits improper operation, press the Reset Button.
How to fix noise on external paging on Panasonic KX-TDA30 PBX?
If you experience noise on external paging with your Panasonic PBX, it might be due to induced noise on the wire between the PBX and the amplifier. Use a shielded cable for the connection, and a short cable is recommended.
Why does PS stay out of service when CS status is changed on Panasonic KX-TDA30?
If the PS (Personal Station) remains out of service after changing the CS (Cell Station) status to In Service on your Panasonic PBX, it might be because the CS takes about 20 seconds to start up. Wait until the CS starts up.
What does it mean when ALARM indicator turns on red on Panasonic PBX?
If the ALARM indicator on the front of your Panasonic PBX cabinet is red, it indicates a major system error. Check the error log using the KX-TDA Maintenance Console.
Why is nothing audible when using speakerphone on Panasonic PBX?
If the speakerphone on your APT or the speakerphone/monitor mode on your DPT is silent on your Panasonic PBX, check the HANDSET/HEADSET selector. If you are not using a headset, ensure the HANDSET/HEADSET selector is set to the "HANDSET" position. Also, check the Personal Programming settings to ensure that the "HEADSET" mode is not selected. If it is, change it to "HANDSET" mode.
Why does PS become out of range on Panasonic PBX?
If the PS (Personal Station) on your Panasonic PBX goes out of range or you cannot make calls, the Cell Station (CS) might not be working correctly or is poorly located, or the access system of the PS is not properly set. Ensure the cable is properly connected to the CS with correct pin assignments and without short circuits. Also, locate the CS properly. Finally, change the access system setting of the PS to the appropriate system or automatic.
Why can't I send a call waiting tone on Panasonic KX-TDA30 PBX?
If you cannot send a call waiting tone to the dialled extension on your Panasonic PBX, it could be because the other party has not set the Call Waiting feature, or the other party has set Data Line Security.
Why did PC and fax machine communication fail on Panasonic PBX?
If the PC and fax machine communication failed on your Panasonic PBX, an indication tone may have interrupted communication.
Why can't I make outside calls or transfer calls on my Panasonic phone?
If originating an outside call, call transfer, or conference cannot be performed on your Panasonic telephone, program the CO button. Refer to "1.20.2 Flexible Buttons" in the Feature Guide.
General| Number of users | 52 user(s) |
|---|---|
| DECT connectable | Yes |
| Number of DECT cell stations | 4 |
| RS-232 ports | 1 |
| RJ-11 ports quantity | 2 |
| AC input voltage | 110-240 V |
| AC input frequency | 50 - 60 Hz |
| Power consumption (typical) | 55 W |
Weight and Dimensions| Weight | 3500 g |
|---|---|
| Dimensions (WxDxH) | 275 x 117 x 376 mm |
Covers various methods for making calls using the PBX system.
Covers various operations that can be performed while on a call.
Explains how to forward incoming calls to a specified destination.
Explains the answering machine service provided by the PBX when an SVM card is installed.
Explains controlling status (Log-in, Log-out, Wrap-up) within an incoming call distribution group.
Allows supervisors to monitor and control call status and extension logs for ICD groups.
Explains how hotel operators use telephones to manage guest room status and set wake-up calls.
Offers solutions for common problems encountered with the telephone system.
