To Next PageTo Next Page
What to do if my Panasonic KX-UT136 unit is not performing properly?
If the unit is not performing properly, check that all cables or cords are properly connected. Also, your connection settings may be incorrect; consult your administrator to confirm that your settings are correct. If the problem persists, consult your dealer. Finally, if an error has occurred, try restarting the unit.
Why does sound cut out and I can hear myself through the speaker on my Panasonic KX-UT136?
This issue can occur for several reasons: * You are too far away from the microphone, so try speaking closer to it. * The environment is not suited to speakerphone calls. Do not use the unit near noise emitting devices. If in a room with windows, close the curtains or blinds. * The unit was moved during a call, so do not move the unit while on a call. * Objects are obstructing the microphone, so keep hands and objects away from the unit during calls. * The other party is using a half-duplex speakerphone. For best performance, the other party should use a full-duplex speakerphone.
Why is the Message/Ringer lamp lit on my Panasonic KX-UT136 IP Phone?
The Message/Ringer lamp lights up when you receive a voice message while you were on the phone or away from your desk. Check the voice message.
What to do if I cannot make long distance calls on my Panasonic KX-UT136?
If you cannot make long distance calls, make sure that you have subscribed to your telephone company’s long distance service, as your telephone service may not allow you to make long distance calls.
What to do if the line is disconnected while talking to an outside party on my Panasonic KX-UT136 IP Phone?
If the line is disconnected while talking to someone, your phone system/service may impose a time limit on outside calls. Consult your dealer to extend the time limit, if necessary.
What does the 'Check LAN cable' message mean on my Panasonic KX-UT136 and how to fix it?
The 'Check LAN cable' message means the LAN cable is not connected. Check all connections.
What to do if I cannot hear a dial tone on my Panasonic IP Phone?
If you cannot hear a dial tone, confirm that the LAN cable is properly connected.
What does 'Memory Full' mean on my Panasonic KX-UT136 IP Phone and how to fix it?
The 'Memory Full' message indicates that a new entry for the phonebook or call block list cannot be stored because the phonebook or call block list is full. Delete unneeded entries.
What does 'No Entries' mean on my Panasonic IP Phone and how to resolve it?
The 'No Entries' message means that the phonebook or call block list contains no entries. Store entries in the phonebook or call block list.
What does 'Please wait…' mean on my Panasonic KX-UT136 IP Phone?
The 'Please wait…' message indicates that the unit is still starting up. If you have a lot of entries in the phonebook list, the unit may take a while to start up. This is normal.
General| Ethernet Ports | 2 |
|---|---|
| Power over Ethernet | Yes |
| Lines | 6 |
| SIP Accounts | 6 |
| Speakerphone | Yes |
| Headset Port | 2.5 mm |
| Operating Temperature | 0 °C to 40 °C |
| Humidity | 10% to 90% (non-condensing) |
| Audio Codec | G.711, G.722, G.726, G.729a |
| Network Interface | 10/100 Mbps Ethernet |
| Protocols | SIP |
Safety guidelines to reduce risk of injury, electric shock, fire, and damage.
Troubleshooting steps for unit malfunction and recommendations for preventing data loss.
Precautions for power connections, placement, and wall mounting.
Measures for network security and important safety instructions.
Diagrams and numbering of controls for KX-UT113X/KX-UT123X and KX-UT113NE/KX-UT123NE models.
Diagrams and numbering of controls for KX-UT133X and KX-UT113RU/KX-UT123RU models.
Diagrams and numbering of controls for KX-UT133NE and KX-UT133RU models.
Diagrams and numbering of controls for KX-UT136X and KX-UT136NE models.
Diagrams and numbering of controls for KX-UT136RU and KX-UT248X models.
Diagrams, numbering of controls, and LCD details for KX-UT248NE/RU models.
Explanation of soft buttons (S1-S4) and their indicator lamps.
Description of Navigator, ENTER, Handset Hook, and function buttons.
Explains soft button icons, scroll indicator, and flexible button display.
Table of icons like FWD/DND, AUTO ANS, ECO, etc., and their meanings.
Explains accessing functions via soft buttons and lists icons with their descriptions.
Table listing more icons and their descriptions (Answer, End, Reject, etc.).
Methods for picking up/hanging up the handset and enabling hands-free conversations.
How to adjust ringer, handset, headset, and speaker volume.
Basic methods for initiating calls and using the phonebook.
Basic methods for handling incoming calls and call rejection.
Methods for calling from logs, redialing last number, and one-touch operations.
Configuring call forwarding and Do Not Disturb settings.
How to transfer calls to another party, including one-touch.
Making, removing parties from, and ending conference calls.
Explains DN, BLF, ACD, Wrap Up, One-Touch, and Headset buttons.
Overview of configurable settings like Ringer, Network, FWD/DND.
Viewing unit information and configuring network parameters.
How to use the Web-based interface for configuring settings and features.
Steps before and during wall mounting the unit.
Solutions for general unit problems.
Lists error messages and their possible causes and solutions.
Solutions for making/receiving calls and sound quality problems.
